Mitel Fax Memo Manual

CP 5011 
Add or Delete Feature Bits 
Pagelofl 
VoiceMemo Release 6.OA and later 
This procedure describes how to add or delete feature bits in an FCOS. 
step 
1. Reach the System Configuration Menu, then go to the Feature Class of Service Menu. 
2. Identify the FCOS you want to add bits to or delete bits from. 
Select: (C) Current FCOS 
Prompt: FCOS to modify = 
Response: Number of the FCOS (l-64OJ you want to add a bit to or delete a 
feature bit from, or just press 
Enter if the displayed FCOS is the...

CP 5015 
Verify Configuration Parameters 
Page 1 of 2 
VoiceMemo Release 6.OA and later 
This procedure describes how to verify the configuration parameters that have been 
entered. This procedure can be used for any of these applications: 
l VoiceMemo l RS-232 Message Waiting Lights 
l DID VoiceMemo l DTMF-to-PBX Message Waiting Lights 
l Paging l Integrations and other optional features 
l Message delivery 
SteD Reference 
@D All Applications Except Paging and Message Delivery ’ 
1. 
Reach the Main...

CP 5015 
Page 2 of 2 
VoiceMemo Release G.OA and later 
Step Reference 
Prompt: Biter group nmibr to display (l-24) or  for all : 
Response: The number of the line group to which the application is assigned. 
Examples of valid formats for this response are: 
l 1 to report the configuration of line group 1 
l 14 to report the configuration of line groups 1 through 4 
l 1,2,4-7 to report the configuration of line groups 1,2, and 4 
through 7 
l Press Enter to get the configuration of all line groups 
The...

cp 5402 
Install Optional Feature With System Online 
Pagelof2 
VoiceMemo Release 6.OA and later 
The procedure describes how to install an optional feature with the system online. Be 
sure the Optional Feature Diskette(s) and the Module Enable Diskette contain the serial 
number(s) for all disk(s) in the system. 
Note: The serial number on the OneView Optional Feature diskette must match the 
serial number of the hard disk on which OneView is being installed. If you 
receive an error message about an...

CP 5402 
Page 2 of 2 
VoiceMemo Release G.OA and later 
step 
6. The following prompt appears: 
Prompt: Wait for paging queues to be empty? 
Response: N to continue. 
7. Exit to the VoiceMemo Configuration - Main Menu, then go to the VoiceMemo 
Configuration - Offline Menu. 
8. Duplicate the active configuration. 
Select: 
(B) Duplicate Active Configuration 
9. Exit to the VoiceMemo Configuration - Main Menu and activate the configurkon. 
Select: (A) Activate Configuration 
Dw. Rev. A 
Reference 
Menu...

cl? 5700 
Shut Down a System 
Page 1 of 2 
VoiceMemo Release 6.OA and later 
This procedure describes how to shut down a module or an entire Series 6 server. You 
should use this procedure before turning off the power to a module, as the shutdown 
command halts call processing in a clean and orderly fashion. 
WARNING! 
You should follow the policies of the site to warn users prior to the system 
shutdown. This process removes the system from call processing. Centigram 
recommends that you perform this...

a? 5700 
Page 2 of 2 
VoiceMemo Release 6.OA and later 
step 
6. Specify if changes to the status of each module are to be made. 
Prompt: Enable or Disable Modules? 
Response: Y to change the status of modules, 
N to keep the module status the same and continue at step 11 
7. Ifyou answered yes in step 6, achartwith~e~ofeachmoduleisdisplayedand~~ehe 
Module Maintenance Menu is displayed. 
8. Enable a module, if necessary: 
Select: (E) ENABLE a module 
Prompt: Which Module? 
Response: The 
number of the...

cp 6449 
Add FaxMemo to a Series 6 Server 
Page lof 1 
VoiceMemo Release 6.OA and later 
This procedure describes how to add FaxMemo capabilities to a Series 6 server. After 
completing this procedure, you must configure one or more of the FaxMemo 
applications. 
Note: If your Series 6 server was configured with FaxMemo at the factory, the 
fax cards and fax software have already been installed. 
3 
WARNING! 
F 
/I This process requires the system to be shut down, resulting in loss of call 
processing...