Lucent Technologies Octel 100 Implementation And Service Manual

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-83
 
 If Set Too Low Hang-up strings may be ignored if the switch cannot send the digits fast
enough to meet this value. This may cause excessive off hook times between
calls.
 
 Min
 0
 Max
 30000
 Default
 0
 Requires Restart
 Yes
 Switch-Dependent
 Yes
 Set by Integrator
 Yes
 
  Hangup Detection Parameters
 
Minimum
Duration for
Drop in Loop
Current
(LCDTIME)  This parameter specifies the amount of time, in 10...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-84
 
 If Set Too High If this parameter is set too high, the system records silence. Also, switches
could detect a port as available and mistakenly pass incoming calls to a port
on which the system is recording silence (missed disconnect). In this case, a
new caller would append to the previous recording.
 
 If Set Too Low If this parameter is set too low, callers could be cut off during recording due
to natural...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-85
 
 Min
 —
 Max
 —
 Default
 No
 Requires Restart
 Yes
 Switch-Dependent
 Yes
 Set by Integrator
 No
 
  Port Parameters
 
Ring Count  This parameter specifies the number of rings each port must hear before it
answers an incoming call. For example, if Ring Count is set to 2, a port must
ring twice before it comes off hook to answer an incoming call.
 
 When/How to Use Enter the Ring Count in the corresponding...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-86
  Port Parameters
 
Outbound  This parameter determines whether each port is allowed to perform outbound
events: message indicators, message notification, AMIS, fax, V-Edit, Visual
Mailbox, future delivery, auto forward, and wake-up calls.
 
 When/How to Use Enable Outbound for each port that should be allowed to perform outbound
events. If you want to dedicate the port to receive outbound calls, disable...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-87
  Port Parameters
 
Outbound Usage
Permitted/Msg
Delivery  This parameter determines whether each port is allowed to perform message
delivery events—message notification and future delivery. To use message
notification and future delivery, you must enable at least one port for Msg
Delivery.
 Msg Delivery is dimmed if Outbound is disabled.
 
 When/How to Use Enable Msg Delivery for each port that should be...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-88
 
 When/How to Use Enable Msg Indicator for each port that should be allowed to perform
message indicator events. If you want to dedicate the port to message
indicator events, disable Inbound as well as all Outbound Usage Permitted
options except Msg Indicator.
 If you experience delayed indicator events, increase the number of ports
enabled for Msg Indicator.
 If you disable a port for Msg Indicator that was...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-89
 
 Related Parameters/Features If the sentinel does not support OctelNet and AMIS, the OctelNet/AMIS
checkbox is disabled for all ports.
 You must enable an outbound network option (Casual AMIS, Administered
AMIS, OctelNet) in the subscribers’ Class of Service for outbound network
messaging to be available.
 You must enable Permit Outbound and enter the system location information
on the Networking tab in...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-90
  Port Parameters
 
Outbound Usage
Permitted/
Application  This parameter determines whether each port is allowed to support external
applications (Visual Mailbox, V-Edit). To support one or both of these external
applications, you must enable at least one port for Applications.
 Applications is dimmed if Outbound is disabled.
 
 When/How to Use Enable Applications for each port that should be allowed to...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-91
 
 Min
 
—
 Max
 
—
 Default
 
Yes
 Requires Restart
 Yes
 Switch-Dependent
 Yes
 Set by Integrator
 No
 
  Voice System Parameters
 
Maximum Call
Duration
(PROGTIME)  This parameter specifies the maximum amount of time, in minutes, the
messaging system allows a call to occupy a port before it disconnects the call
without warning.
 
 When/How to Use Use caution when setting this parameter. If callers are...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-92
Related Parameters/FeaturesW hen RECDTMF is set to a higher value than PLAYDTMF, the RECDTMF
value is used for both.
If Set Too HighIf this parameter is set too high, the system may not recognize DTMF tones
and will not interrupt the prompt. If the DTMF is not recognized, OctelNet
messages may be missed.
If Set Too LowIf this parameter is set too low, the system may interpret voice data as DTMF.
If the DTMF is...