Lucent Technologies Octel 100 Implementation And Service Manual

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-33
 
 Related Parameters/Features The Country Code is placed in front of the System Telephone Access Number
to identify the messaging system for remote sites.
 
 If Set Too High Not applicable.
 
 If Set Too Low Not applicable.
 
 Min
 0
 Max
 15
 Default
 Blank
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  Networking Parameters
 
Network Prefix  This parameter defines the code that the...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-34
  Networking Parameters
 
International
Access Code  This parameter defines the code used to access international dialing in the
country in which the messaging system is located. The system uses this code
when sending network replies to remote systems in other countries.
 The system determines whether the International Access Code is required for
a reply by comparing the Country Code of the remote destination...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-35
 
 If Set Too Low Not applicable.
 
 Min
 0
 Max
 3
 Default
 1
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  Networking Parameters
 
Country Code  This parameter defines the dialing code for the country in which the
messaging system is located.
 The system transmits the Country Code to remote systems when it
dispatches both casual and administered network messages. This allows
remote...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-36
  Networking Parameters
 
Dispatch
Options/Permit
Outbound  This parameter determines whether the messaging system can send network
messages and replies.
 
 When/How to Use Permit Outbound controls the ability to send network messages and replies
from the system.
 
 Related Parameters/Features You must also activate the networking options on the Class of Service dialog
box.
 The Network Mailbox Forwarding...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-37
 
 Min
 —
 Max
 —
 Default
 11:00 PM
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  Networking Parameters
 
Economy
Hours/Starting
Weekend Time  This parameter defines the system-wide start of Economy dispatch hours for
the weekend. During Economy hours, the system sends any casual or
administered network messages marked for Economy dispatch since the end
of Economy Hours on the previous...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-38
extend into Monday are still considered part of the weekend Economy time.
 
 Related Parameters/Features You can use the Economy Dispatch fields on the Network Node Maintenance
dialog box to override Economy Hours for individual nodes.
 The Starting W eekend Time determines when Economy Hours begin.
 
 If Set Too High Not applicable.
 
 If Set Too Low Not applicable.
 
 Min
 —
 Max
 —
 Default
 6:00 AM...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-39
  Networking Parameters
 
Maximum
Number of
Attempts Before
Failure  This parameter defines the allowed number of unsuccessful dispatch
attempts to an Administered node before the system deactivates the node.
W hen a node is inactive, subscribers cannot send any messages to it until it
has been reactivated on the Network Node Maintenance dialog box.
 This parameter only applies to OctelNet and Administered AMIS...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-40
 
 When/How to Use W hen setting this parameter, keep in mind that only one message in the
queue will be held for the maximum delay. When the delay is reached, the
system sends all messages in the queue, regardless of how long they have
been there.
 Consider what type of messages subscribers usually send with standard
dispatch. If time-critical messages are regularly sent with standard dispatch,
you may want to...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-41
 
 Related Parameters/Features This parameter defines the maximum messages for queued dispatch on a
system-wide basis. You can override this parameter for individual nodes
using the Standard Dispatch Maximum Messages field on the Network Node
Maintenance dialog box.
 If Maximum Delay for Queued Dispatch in Minutes parameter in System
Setup or Maximum Delay or Maximum Messages on the Network Node
Maintenance...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-42
 
  Networking Parameters
 
No Answer/Delay
(in Minutes)  This parameter defines the number of minutes the messaging system waits
between retries when dispatching to a remote access phone number that
does not answer. This parameter applies to all outbound network messaging
(OctelNet, Administered AMIS, Casual AMIS, Network Replies).
 
 When/How to Use The default for this parameter should be sufficient for most...