Lucent Technologies Octel 100 Implementation And Service Manual

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-23
  Min
 0
 Max
 99
 Default
 5
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
  Message Timing Parameters
 
Maximum Time to
Record Mailbox
Prompts This parameter specifies the maximum amount of time, in seconds, for
subscribers to record mailbox prompts and folder labels.
 When/How to Use For most systems, the default setting should be sufficient.
 Some applications may require longer...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-24
  Min
 0
 Max
 9
 Default
 2
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 Subscriber Parameters (Page 6 of 26)
  The Subscriber parameters control password security features and message maintenance features for
subscriber mailboxes.
 
  Subscriber Parameters
 
Permit
Subscribers to
Leave Messages
to Themselves  This parameter allows subscribers to send messages to their own mailboxes.
W...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-25
 
 Min
 —
 Max
 —
 Default
 No
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  Subscriber Parameters
 
Enable
Confirmation of
Deleted
Messages  This parameter determines whether the system prompts subscribers to
confirm that they want to delete a message by pressing .
 
 When/How to Use For most systems, leave this parameter enabled to help prevent subscribers
from accidentally deleting...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-26
  Subscriber Parameters
 
Voice Warning
when Message
Time is Less
than 2 Minutes  This parameter does not affect messaging system performance and should
be left at the default.
 
  Subscriber Parameters
 
Maximum
Number of
Forwarded
Extensions  This parameter determines the maximum number of extensions the system
allows in a forwarding chain when the desired extension is busy or not
answered. W hen this maximum...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-27
  Subscriber Parameters
 
Consecutive
Login Failures
Before Lock-Out  This parameter specifies the maximum number of failed mailbox login entries
allowed before the system locks the mailbox. A single failed login entry is
logged when a caller attempting to log into a mailbox exceeds the Maximum
Number of Errors (as defined on the Operator tab in System Setup). This
feature is used as a security measure to...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-28
  Subscriber Parameters
 
Minimum Length
of Password  This parameter specifies the minimum number of digits the system requires
for a valid mailbox password. This parameter is used as a security feature to
require subscribers to use passwords to log into their mailboxes.
 
 When/How to Use For most systems, the default should be sufficient.
 If you change this parameter to a higher value, the system prompts...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-29
  Subscriber Parameters
 
Initial Password
for New
Mailboxes –
None Required  This parameter determines whether the system requires subscribers logging
into new mailboxes to enter a password.
 
 When/How to Use W hen you select this option, the system allows a subscriber logging into a
new mailbox to gain immediate access to the mailbox.
 Subscribers may assign a password to their individual mailboxes even...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-30
  Subscriber Parameters
 
Initial Password
for New
Mailboxes –
Random
Generator
Method  This parameter determines whether the system assigns random passwords to
new mailboxes. W hen you enable this parameter, the system automatically
assigns a series of digits equal in length to the Minimum Length of Password
to each new mailbox that is created.
 W hen you create new mailboxes through the screen interface using...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-31
 
 When/How to Use This parameter should be enabled for most systems. If you disable it, callers
could become frustrated by having to call back to leave additional messages.
 An application for which you may want to disable this parameter is a service
bureau, where you want callers directly routed to subscriber mailboxes to
leave a message and then disconnected. Also, on smaller systems, such as
those with...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-32
 Networking Parameters (Page 8 of 26)
  The Networking parameters identify the local messaging system and define system-wide defaults for
dispatching network messages. Some of these parameters can be ov erridden on a per-node basis on the
Network Node Maintenance dialog box. Networking parameters only apply to messaging systems with
sentinels that support one or both of the network protocols, OctelNet and...