Lucent Technologies Octel 100 Implementation And Service Manual

13. Setting Up the System
Implementation and Service Manual  Searc hing f or a Partic ular Sys tem Setup Parameter13-3
Searching for a Particular System Setup Parameter
If you are not sure what tab a certain parameter is located on, you can search for the
parameter by the parameter name.
To locate a specific System Setup parameter:
1.  From the Search menu in System Setup, select Find. The Find First dialog box
displays.
 
2.  In the Text to find field, enter the name, or part of the name, of the...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-4
System Setup Parameters List
System Setup is comprised of 26 tabs that contain parameters grouped by a specific
feature or function, such as Operator parameters and Networking parameters. To access
a particular feature’s parameters, click the corresponding tab.
The following list references each System Setup parameter by tab and page number.
General Parameters (Tab 1 of 26)...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-5
Initial Password for New Mailboxes - None Required..........................................13-29
Initial Password for New Mailboxes - Set to Default ............................................13-29
Initial Password for New Mailboxes - Random Generator Method.......................13-30
Caller Parameters (Tab 7 of 26) .............................................................................13-30
Permit...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-6
Intercom Paging Parameters (Tab 13 of 26) .........................................................13-55
Intercom Paging Code ........................................................................................13-55
Release Code for Intercom Paging.....................................................................13-56
Repeat Intercom Paging...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-7
Seconds to W ait for DID (DIDTIME)....................................................................13-79
Number of Milliseconds to W ait for Digits............................................................13-80
Off Hook Delay Time (OFFHDLY).......................................................................13-80
Activ ate Digit Grabber...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-8
General Parameters (Page 1 of 26)
The General parameters control general system-lev el functions.
General Parameters
Enable
Automated
AttendantThe Automated Attendant routes calls to messaging system extensions.
W hen the Automated Attendant is disabled, the messaging system routes
callers directly to the subscribers’ mailboxes. It does not attempt to transfer
calls to subscriber extensions.
Note that this...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-9
  General Parameters
 
Number of Digits
in a Mailbox  This parameter determines the length and available range of subscriber
mailboxes. For example, if you set this parameter to 5, the range of available
mailboxes is 10000 to 99999.
 
 When/How to Use You must set this parameter using the System Setup before you begin
creating subscriber mailboxes. If you change the value of this parameter after
you have created...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-10
 
 If Set Too Low A low setting for this parameter does not affect messaging system
performance. Setting it to 0 would disable the parameter and is not
recommended.
 
 Min
 0
 Max
 99
 Default
 5
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  General Parameters
 
Tutor for New
Mailboxes  This parameter determines whether Call Educator, the messaging system
tutorial, is enabled for...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-11
  General Parameters
 
Shutdown
System After
Daily
Maintenance  This parameter determines whether the messaging system goes through an
automatic shutdown after daily maintenance is complete. After the system
shutdown is complete, the user-supplied third-party utilities specified in the
RUNVM.CMD file execute and the messaging system restarts.
 
 When/How to Use Enable this parameter if you want to run...

13. Setting Up the System
Implementation and Service Manual  System Setup Parameters List13-12
 
 If Set Too Low Not applicable.
 
 Min
 —
 Max
 —
 Default
 No
 Requires Restart
 No
 Switch-Dependent
 No
 Set by Integrator
 No
 
  General Parameters
 
First Personal
Group List
Number  This parameter determines the first number and defines the range for the 10
personal group lists available to each subscriber mailbox.
 
 When/How to Use The First Personal Group List Number must be at least 10 less than...