Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-99 Add a Switch Node Carrier (Standard Reliability) 
6
Prepare New Switch Node Carrier D
1. Visually insp ec t the new J58890SA Switc h Node Carrier for any d amag e. 
Verify that the bac kp lane p ins are not b ent.
NOTE:
The enhanc ed  R8r PPN AC c arrier may look d ifferent than the other 
c arriers bec ause it c omes with 16 new g round ing...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-100 Add a Switch Node Carrier (Standard Reliability) 
6
Install New Switch Node Carrier 
1.Install the switc h nod e c arrier into p osition “ D”  b y lining  up  the p lastic  
alig nment tip s on the top  rear of the c arrier with the sc rew holes in the 
c ab inet. These alig nment tip s sup p ort the c arrier while the sc rews are 
b eing  rep...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-101 Add a Switch Node Carrier (Standard Reliability) 
6
Figure 6-35. Locations of Top and Bottom Ground Straps on Standard and 
Enhanced Carriers
8.If the switc h nod e c arrier was installed in the “ D”  position of the PPN, 
install the TDM/LAN c able (b etween the “ A”  and  “ D”  c arriers) to the 
pin-field block labeled “TDM/LAN” on the right...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-102 Add a Switch Node Carrier (Standard Reliability) 
6
9.If a switc h node c arrier was installed  in the “ D”  p osition, verify that the 
ZAHF4 TDM/LAN b us terminator is installed  at slot 02 of the switc h nod e 
carrier “D”. See Figure 6-36
.
If a switc h nod e c arrier is b eing  installed  in the “ E”  p osition, verify that the 
ZAHF4...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-103 Add a Switch Node Carrier (Standard Reliability) 
6
Figure 6-36. TDM/LAN Connections for Standard Reliability R8r EPN Figure Notes
1.Port Carrier (“ C” Position)
2. Port Carrier (“ B”  Position)
3. Proc essor Carrier (“ A”  Position)4.  Switc h Nod e Carrier (“ D”  Position)
5. TDM/LAN Bus Terminator (ZAHF4)
6. TDM/LAN Cab le (WP91716 L7) 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-104 Add a Switch Node Carrier (Standard Reliability) 
6
Install Circuit Packs
1.Install the new c irc uit p ac ks into c arrier “ D.”  Use the d ec al and  the 
up g rad e c onfig uration doc ument (p rovid ed  with the eq uip ment) as a 
guide.
2. Install c irc uit p ac k b lanks in slots not eq uip p ed  with c irc uit p ac ks.
Interconnect Port...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-105 Add a Switch Node Carrier (Standard Reliability) 
6
4. Behind  p ort c arrier B of eac h EPN c ab inet:
a. Install a lig htwave transc eiver on c ab le c onnec tor at slot 1B02.
b . Connec t the other end  of the fiber op tic  c able to the lig htwave 
transc eiver, just installed .
c . Carefully attac h the fib er op tic  c ab le (with c ab le...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-106 Add a Switch Node Carrier (Standard Reliability) 
6
Reseat DEFINITY LAN Gateway System
1. Reseat the LAN Gateway assemb ly into its b ac kp lane c onnec tors.
Reseat DEFINITY AUDIX System
1. Reseat the AUDIX assemb ly to its b ac kp lane c onnec tors.
Power Up System
1. At the c ab inet c ontaining  the new switc h nod e c arrier, set the main c...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-107 Add a Switch Node Carrier (Standard Reliability) 
6
Resolve Alarms and Enable Alarm Origination
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r
.
2. If the Alarm Origination Activated f
ield  ad ministration that you 
p reviously noted  is alread y set to y
, be sure...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-108 Add a Switch Node Carrier (High or Critical Reliability) 
6
Add a Switch Node Carrier (High or 
Critical Reliability)
To upg rad e to a hig h or c ritic al reliability R8r, a sec ond  switc h nod e c arrier is 
ad d ed  either to an emp ty “ E”  c arrier p osition of an existing  multic arrier p ort 
network or to the “ D”  c arrier p osition (as...