Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

SEATS
76-5-2 REPAIRS
Front seat 
$% 78.10.44.99 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Raise seat cushion.
2.Remove bolt securing seat belt to front seat.
3.Remove nut caps and remove 2 nuts securing 
front of seat.
4.Move the seat forward.
5.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS) 
Precautions.
WARNING: Always...

SEATS
REPAIRS 76-5-3
Rear seat
$% 78.10.48.99
Remove
1.Fit protection to wheel arch.
2.Remove 2 bolts securing rear seat.
3.Release  rear seat and roll it forwards.
4.Disconnect multiplug from seat.
5.Remove 2 nuts securing seat and with 
assistance, carefully remove seat from vehicle.
Refit
1.Fit rear seat in fully folded position and tighten 
nuts to 25 Nm (18 lbf.ft).
2.Connect multiplug to seat.
3.Position seat in upright position.
4.Fit bolts securing rear seat and tighten to 25 
Nm (18 lbf.ft)....

SEATS
76-5-4 REPAIRS
7.Release staples securing squab cover to lower 
backboard.
8.Release squab side cover from both sides of 
backboard.
9.Release 2 studs securing lower half of 
backboard.
10.Release backboard from seat.11.Disconnect lumbar harness multiplugs from 
pump and valve.
12.Disconnect multiplug from heated seat circuit.
13.Release harness from retaining clip and feed 
through squab cover.
14.Remove 2 Torx bolts and remove squab frame 
from seat frame.
M78 0616 

SEATS
REPAIRS 76-5-5
15.Release seat cover beading from rear of frame.
16.Release seat cover beading from sides and 
front of frame.
17.Remove seat cushion and cover assembly.
18.Remove 15 hog rings securing cover to 
cushion, remove cover.
Refit
1.Position cover to cushion and secure with hog 
rings.
2.Position and secure cover and cushion 
assembly to frame.
3.Position squab frame to seat frame, fit Torx 
bolts tighten to 25 Nm (18 lbf.ft).
4.Route lumbar harness through squab cover 
and secure to...

SEATS
76-5-6 REPAIRS
Cover - one piece - front seat cushion - 
models with adjustable upper squab
$% 78.30.02
Remove
1.Remove seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
2.Remove switch pack assembly.
 
 +  SEATS, REPAIRS, Switch pack - 
seat memory.
3.Remove screw securing finisher on inner seat 
base, remove finisher.
4.Release 3 backboard tension straps from under 
seat.
5.Remove 2 screws securing lower squab 
finisher.
6.Release lower finisher from 6 retaining clips 
and remove.
7.Disconnect 2...

SEATS
REPAIRS 76-5-7
9.Release beading from squab cover finisher.
10.Release finisher from 4 retaining clips and 
remove.
11.Carefully release 2 retaining clips securing  
headrest to motor housing.
12.Remove headrest.
13.Release retaining strip securing squab cover to 
lower frame.14.Disconnect multiplugs from headrest and upper 
squab motors.
15.Disconnect multiplugs from lumbar pump and 
valve.
M78 0635 

SEATS
76-5-8 REPAIRS
16.Disconnect multiplug from heated seat circuit.
17.Release 2 retaining strips, securing both sides 
of lower squab cover to frame.
18.Release squab harness from 4 retaining clips.
19.Remove 2 Torx bolts securing squab frame to 
seat frame.
20.Remove squab assembly from seat assembly.
21.Release seat cover beading from sides and 
front of frame.
22.Remove seat cover and pad from frame.23.Remove 15 hog rings securing cover to 
cushion, remove cover.
Refit
1.Position cover to cushion...

SEATS
REPAIRS 76-5-9
Cover - rear seat cushion - RH 
$% 78.40.04
Remove
1.Remove seat base finisher.
 
 +  SEATS, REPAIRS, Finisher - seat 
base rear.
2.Remove seat fold mechanism.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
3.Disconnect multiplug from squab harness.
4.Remove Torx bolt securing squab frame to seat 
frame, separate frames.
5.Release seat cover both sides and front 
beading, raise cover and cushion.
6.Release heated seat harness multiplug from 
retaining clip and feed harness through...

SEATS
76-5-10 REPAIRS
Cover - rear seat cushion - LH
$% 78.40.05
Remove
1.Remove LH seat base finisher.
 
 +  SEATS, REPAIRS, Finisher - seat 
base rear.
2.Remove seat fold mechanism.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
3.Disconnect multiplug from squab harness.
4.Remove Torx bolt securing squab frame to seat 
frame, separate frames.
5.Release seat cover both sides and front 
beading, raise cover and cushion.
6.Release heated seat harness multiplug from 
retaining clip and feed harness...

SEATS
REPAIRS 76-5-11
Refit
1.Position seat cover to cushion and secure with 
hog rings.
2. Fit 14 staples securing cover under cushion.
3.Position cushion to frame and secure rear of 
cover.
4.Fit stud securing rear cover.
5.Feed heated seat harness through seat frame 
and secure multiplug to retaining clip.
6.Position seatbelt lower buckle to frame and 
secure with Torx bolt tighten to 31 Nm (23 
lbf.ft).
7.Fit seat cover sides and front beading.
8.Fit Torx bolt securing squab frame to seat 
frame,...