Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

INTERIOR FITTINGS
76-3-16 REPAIRS
Finisher - upper - passengers side  
$% 76.46.13
Remove
1.Remove A post upper trim finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - A post - upper.
2.Remove fascia end closing panel.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - fascia end.
3.Remove face level air vent.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Fresh air vent - face level.
4.Remove 3 Torx screws securing upper finisher 
to fascia.
5.Remove screw securing rear of cup holder to 
inner...

INTERIOR FITTINGS
REPAIRS 76-3-17
Finisher - lower - passengers side 
$% 76.46.14
Remove
1.Remove fascia end closing panel.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - fascia end.
2.Remove RH lower A post finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - A post - lower.
3.Remove passenger side footwell closing panel.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - passenger side.
4.Remove cover from lower finisher for access to 
Torx screw.
5.Remove 3 Torx screws securing upper...

INTERIOR FITTINGS
76-3-18 REPAIRS
Fascia - carrier 
$% 76.46.22 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
NOTE: Ensure the harness routing is noted when 
removing the carrier. This will help to ensure that the 
harness is correctly fitted/routed when refitting the 
carrier.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS)...

INTERIOR FITTINGS
REPAIRS 76-3-19
13.Release clip securing harness to drivers side 
footwell duct.
14.Identify position of harness for reassembly.
15.Note position for refit and remove foam strip 
from ends of carrier.
16.Remove 10 Torx screws securing fascia carrier 
and remove carrier.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
17.Remove 3 Torx screws securing drivers side 
footwell duct and remove duct.
18.Remove 3 Torx screws securing LH demister 
duct and...

INTERIOR FITTINGS
76-3-20 REPAIRS
21.Remove 2 remaining Torx screws securing 
passenger side face level vent duct and 
remove duct.
22.Release and remove solar sensor.
23.Remove 6 Torx screws securing heater control 
mounting and remove mounting.
24.Remove 3 Torx screws securing drink holder 
bracket and remove bracket.25.Remove 4 instrument lower finisher securing 
sacks.
26.Remove 6 passenger airbag cover plastic 
retaining nuts.
27.Remove 2 side finisher retaining sacks.
28.Remove 64 speed nuts from...

INTERIOR FITTINGS
REPAIRS 76-3-21
14.Fit clip securing harness to footwell duct.
15.Fit clip securing cassette/CD harness.
16.Connect solar sensor multiplug.
17.Fit clip securing instrument pack harness.
18.Fit and secure steering column gaiter.
19.Fit instrument pack lower finisher.
20.Fit instrument pack.
 
 +  INSTRUMENTS, REPAIRS, 
Instrument pack.
21.Fit cassette/CD unit.
 
 +  NAVIGATION AND IN CAR 
ENTERTAINMENT, REPAIRS, Cassette/CD 
unit.
22.Fit footwell closing panels.
 
 +  INTERIOR FITTINGS,...

INTERIOR FITTINGS
76-3-22 REPAIRS
14.Remove drivers side fascia finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - upper - drivers side.
15.Remove passenger side fascia finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - upper - passengers side.
16.Remove gearshift selector assembly.
 
 +  AUTOMATIC TRANSMISSION - GM 
5L40-E, REPAIRS, Lever - gearshift selector 
assembly.
17.Remove 4 nuts securing selector carrier to 
body and remove.
18.Cover studs to prevent damage to fascia on 
removal....

INTERIOR FITTINGS
REPAIRS 76-3-23
23.Noting fitted position, remove nut and 
disconnect arm from wiper motor.
24.Remove 3 bolts securing wiper motor to 
mounting bracket, collect motor and move 
aside for access.
25.Remove 2 bolts securing fascia to bulkhead.26.Remove 2 Allen bolts securing A/C pipes to 
bulkhead, disconnect pipes and discard O 
rings.
CAUTION: Immediately cap all A/C pipes to 
prevent ingress of dirt and moisture into the 
system.
27.Position container to collect coolant.
28.Release...

INTERIOR FITTINGS
76-3-24 REPAIRS
32.Disconnect 2 multiplugs and release harness 
clip from A post, adjacent to top rail. Repeat on 
opposite side. Tape disconnected leads to 
windscreen.
33.Withdraw fascia sufficiently to disconnect A 
post airbag multiplugs.
34. Passenger side only: Release 2 additional A 
post harness clips.
35.Remove transfer box ECU.
 
 +  TRANSFER BOX, REPAIRS, 
Electronic control unit (ECU) - transfer 
gearbox.
36.Disconnect positive feed from bulkhead fuse 
box.
37.Disconnect...

INTERIOR FITTINGS
REPAIRS 76-3-25
44.Remove 2 bolts securing E box to suspension 
turret, move aside for access.
45.Release air intake duct from inner wing and 
remove.
46.Remove nuts and disconnect harness earth 
headers.
47.Remove front bumper.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Bumper - assembly - front.48.Disconnect hose from rear washer pump.
49.Release 4 cable ties securing washer hose to 
armature and move hose aside.
50.Disconnect horn multiplugs.
51.Remove indicator lamp.
 
 +  LIGHTING,...