Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

SEATS
76-5-22 REPAIRS
Motor - squab 
$% 78.70.21
Remove
1.Remove seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
2.Remove Allen bolt securing arm rest.
3.Remove armrest from boss.
4.Remove headrest.
5.Release 3 backboard tension straps from under 
seat.6.Release staples securing squab cover to lower 
backboard.
7.Release squab side cover from both sides of 
backboard.
8.Release 2 studs securing lower half of 
backboard.
9.Release backboard from seat.
10.Disconnect multiplugs from headrest and upper...

SEATS
REPAIRS 76-5-23
11.Disconnect multiplugs from lumbar pump and 
valve.
12.Disconnect multiplug to heated seat circuit.
13.Release harness from 4 retaining clips.14.Remove 2 Torx bolts and remove squab frame 
from seat frame.
15.Remove 2 E clips securing motor assembly.
16.Carefully prise motor assembly from mounting 
bosses and release drive cable from assembly.
M78 0616 

SEATS
76-5-24 REPAIRS
Refit
1.Position and fit drive cable to motor assembly.
2.Carefully fit motor assembly to mounting 
bosses.
3.Fit E clips securing motor assembly.
4.Position squab frame to seat frame, fit Torx 
bolts tighten to 25 Nm (18 lbf.ft).
5.Position harness and secure retaining clips.
6.Connect multiplugs to headrest and squab 
motor.
7.Connect multiplug to heated seat circuit.
8.Connect lumbar harness multiplugs to lumbar 
pump and valve.
9.Position backboard to seat assembly, fit studs...

SEATS
REPAIRS 76-5-25
Motor - rise & fall - front seat 
$% 78.70.27
Remove
1.Remove seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
2.Disconnect multiplug from rise and fall motor.
3.Remove 2 Torx bolts securing rise and fall 
motor and remove motor.
Refit
1.Position rise and fall motor and secure with 
Torx bolts, tighten to 10 Nm (7 lbf.ft). 
2.Connect multiplug to rise and fall motor.
3.Fit seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
Motor - rise & fall - head rest - front seat 
$% 78.70.31...

SEATS
76-5-26 REPAIRS
6.Release 2 studs securing lower half of 
backboard.
7.Release squab side cover from both sides of 
backboard.
8.Release backboard from seat.
9.Release headrest from motor assembly and 
remove from seat.
10.Disconnect multiplug from headrest rise and fall 
motor.
11.Release motor assembly from retaining clips 
and remove from frame.
Refit
1.Position motor assembly to frame and secure in 
retaining clips.
2.Connect multiplug to headrest rise and fall 
motor.
3.Fit head rest in seat...

SEATS
REPAIRS 76-5-27
Switch - front seat control 
$% 78.70.89 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Raise seat cushion.
2.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS) 
Precautions.
WARNING: Always disconnect both battery 
leads before beginning work on the SRS 
system. Disconnect the negative lead first. 
Never reverse...

SEATS
76-5-28 REPAIRS
Switch pack - seat memory 
$% 78.70.91
Remove
1.Raise seat.
2.Remove screw securing rear of outer valance.
3.Carefully release 3 retaining clips securing 
outer valance.
4.Release switch pack from 3 retaining clips.
5.Disconnect 4 multiplugs and remove switch 
pack.
Refit
1.Connect 4 multiplugs to switch pack.
2.Fit switch pack to outer valance and secure 3 
retaining clips.
3.Position outer valance to seat base and secure 
3 retaining clips.
4.Fit screw to secure rear of seat...

SEATS
REPAIRS 76-5-29
Latch - rear squab 
$% 78.80.05
Remove
1.Remove squab cover and pad from frame.
 
 +  SEATS, REPAIRS, Cover - squab - 
rear seat - RH.
2.Remove and discard retaining clip securing 
operating rod to latch assembly.
3.Release operating rod from assembly.
4.Remove 2 Allen bolts securing latch assembly 
to frame, remove assembly.
Refit
1.Position latch assembly to frame and secure 
with Allen bolts, tighten to 25 Nm (18 lbf.ft).
2.Connect operating rod and secure with 
retaining clip....

SEATS
76-5-30 REPAIRS
3.Remove 2 screws securing lower squab 
finisher.
4.Release lower finisher from 6 retaining clips 
and remove.
5.Disconnect 2 tension straps securing upper 
squab cover.
6.Release velcro strip securing squab cover.7.Release beading from squab cover finisher.
8.Release finisher from 4 retaining clips and 
remove.
9.Carefully release 2 retaining clips securing  
headrest to motor housing.
10.Remove headrest.
11.Release retaining strip securing squab cover to 
lower frame. 

SEATS
REPAIRS 76-5-31
12.Disconnect multiplugs from headrest and upper 
squab motors.
13.Disconnect harness multiplugs from lumbar 
pump and valve.14.Disconnect multiplug from heated seat circuit.
15.Release 2 retaining strips, securing both sides 
of lower squab cover to frame.
16.Release squab harness from 4 retaining clips.
17.Remove 2 Torx bolts securing squab frame to 
seat frame.
18.Remove squab assembly from seat assembly.
19.Release 4 retaining strips securing both sides 
of squab assembly to...