Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

BODY DIMENSIONS
-8 BODY DIMENSIONS
Under body, point to point dimensional information
Item From To Length
A Rear tow bar fixing hole Front sub frame - front fixing hole 4039 (159.015)
B Rear tow bar fixing hole Front subframe, middle mounting hole 3737 (147.125)
C Rear tow bar fixing hole Front subframe, rear mounting hole 3283 (129.251)
D Rear tow bar fixing hole Centre cross member - front fixing hole 2942.8 (115.858)
E Rear tow bar fixing hole Centre cross member - rear fixing hole 2448.8 (96.409)
F...

BODY DIMENSIONS
BODY DIMENSIONS -9
Internal, point to point dimensional information
Fascia carrier mounting points
Item From To Length
A Rear subframe, rear mounting hole, LH Rear subframe, rear mounting hole, RH 1020 (40.157)
Item From To Length
A Fascia carrier mounting hole, RH Fascia carrier mounting slot, LH 1458 (57.401) 

BODY DIMENSIONS
-10 BODY DIMENSIONS
Rear end, point to point dimensional information
Item From To Length
A Upper tailgate - inboard hinge fixing 
hole, LHUpper tailgate - inboard hinge fixing 
hole, RH946.8 (37.275)
B Upper tailgate - gas strut fixing hole, LH Upper tailgate - gas strut fixing hole, RH 1141 (44.921)
C E post drain channel - finisher fixing 
hole, LHE post drain channel - finisher fixing 
hole, RH1326.6 (52.228)
D Lower tailgate hinge fixing - inboard 
hole, LHLower tailgate hinge fixing...

BODY DIMENSIONS
BODY GAPS AND PROFILES -11
BODY GAPS AND PROF ILE S
Gap and Profile Measurements
The following information is to be used as a guide to assist the technician in refitting exterior body panels and trim 
items so as to achieve a correctly aligned and cosmetically acceptable vehicle.
Measurements shown are in millimetres and inches. The measurements shown in brackets are in inches.
Profile of bonnet to headlamp to be flush. Even gaps side to side, tolerance ± 1.0 mm (0.040).
Section Gap...

BODY DIMENSIONS
-12 BODY GAPS AND PROFILES
Section D-D, profile of wing grille to front door is 0.0 nominal, tolerance  +1.0 (0.040) / -0.0.
Section F-F, profile of front door to rear door is 0.0 nominal, tolerance  +1.0 (0.040) / -0.0.
Section G-G, profile of rear door to body side is 0.0 nominal, tolerance  +1.0 (0.040) / -0.0.
Section J-J, profile of rear bumper to body side is 3.5 mm (0.137) nominal, tolerance ± 1.0 (0.040).
Section Gap Description Dimension
C-C c Bonnet to front wing 6.0 (0.236), ±...

BODY DIMENSIONS
BODY GAPS AND PROFILES -13
Section Gap Description Dimension
L-L l Bodyside to upper tailgate  4.0 (0.157), ± 1.0 (0.040)
M-M m Lower tailgate to tail lamp 5.0 (0.196), ± 1.5 (0.059)
N-N n Upper tailgate to lower tail gate 20 (0.787), ± 2 (0.078) 

BODY DIMENSIONS
-14 BODY GAPS AND PROFILES 

PANEL REPAIRS
REPLACEMENT PANELS -1
PANEL REPAIRS REPLACE ME NT PA NELS
Serviceable Panels
Front end panels
1Bonnet locking platform
2LH headlamp mounting panel
3RH headlamp mounting panel
4Radiator protection bar 

PANEL REPAIRS
-2 REPLACEMENT PANELS
Inner front end panels
1Front sidemember assembly
2Front sidemember inner panel
3Front sidemember reinforcement panel
4Front sidemember outer panel
5Valance inner assembly
6Valance inner closing panel
7Valance inner reinforcement
8Brake hose bracket
9Brake pipe support bracket
10Valance outer
11Valance outer extension
12Front bumper mounting bracket 

PANEL REPAIRS
REPLACEMENT PANELS -3
Outer body side panels 
1Front body side assembly
2Rear body side assembly
3Body side assembly