Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

SEATS
76-5-32 REPAIRS
21.Remove 19 hog rings securing squab cover to 
pad, remove cover.
22.Release retaining plate securing headrest 
finisher to squab cover, remove finisher.
Refit
1.Fit headrest finisher to squab cover and secure 
with retaining plate.
2.Position squab cover to pad and secure with 19 
hog rings.
3.Fit squab cover and pad to frame.
4.Fit 4 retaining strips securing both sides of 
squab cover to frame.
5.Position and fit squab assembly to seat 
assembly.
6.Fit squab frame to seat frame,...

SEATS
REPAIRS 76-5-33
Cover - squab - front seat 
$% 78.90.08
Remove
1.Remove seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
2.Remove Allen bolt securing arm rest.
3.Remove armrest from boss.
4.Remove headrest.
5.Release 3 backboard tension straps from under 
seat.6.Release staples securing squab cover to lower 
backboard.
7.Release squab side cover from both sides of 
backboard.
8.Release 2 studs securing lower half of 
backboard.
9.Release backboard from seat.
M78 0613 

SEATS
76-5-34 REPAIRS
10.Disconnect harness multiplugs from lumbar 
pump and valve.
11.Disconnect multiplug from heated seat circuit.
12.Release harness from retaining clip and feed 
harness through squab cover.
13.Remove 2 Torx bolts and remove squab frame 
from seat frame.14.Raise front of squab cover to gain access to 
head rest guides.
15.Release headrest retaining clips, remove 
headrest guides.
16.Remove squab cover and pad from frame.
17.Remove and discard 12 hog rings and remove 
cover from pad....

SEATS
REPAIRS 76-5-35
10.Position lower squab cover to backboard and 
staple.
11.Fit backboard tension straps to under seat 
retaining clips.
12.Fit armrest to boss and secure with Allen bolt, 
tighten to 25 Nm (18 lbf.ft).
13.Fit seat assembly.
 
 +  SEATS, REPAIRS, Front seat.
Cover - squab - rear seat - side - LH
$% 78.90.12
Remove
1.Remove seat base finisher.
 
 +  SEATS, REPAIRS, Finisher - seat 
base rear.
2.Remove seat fold mechanism.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
3.Remove rear...

SEATS
76-5-36 REPAIRS
9.Raise seat cover and cushion, remove and 
discard Torx bolt securing seat belt anchor 
point to frame.
10.Pull seatbelt through cushion and cover, 
remove seat base.
11.Remove 2 screws securing seat belt finisher, 
remove finisher.
12.Release beading securing squab cover to sides 
and bottom of frame.
13.Carefully release 4 clips securing seat release 
button escutcheon, remove escutcheon.
14.Raise squab cover and cushion to gain access 
to headrest guides.
15.Release 3 clips...

SEATS
REPAIRS 76-5-37
Cover - squab - rear seat - RH 
$% 78.90.13
Remove
1.Remove seat base finisher.
 
 +  SEATS, REPAIRS, Finisher - seat 
base rear.
2.Remove seat fold mechanism.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
3.Remove Torx bolt securing squab frame to seat 
frame, separate frames.
4.Disconnect multiplug to heated squab.
5.Remove rear squab finisher.
 
 +  SEATS, REPAIRS, Finisher - rear 
seat squab.
6.Release beading securing squab cover to sides 
and bottom of frame.7.Carefully...

SEATS
76-5-38 REPAIRS
11.Remove 16 hog rings securing cover to 
cushion, remove cover.
Refit
1.Position cover to cushion and secure with hog 
rings.
2.Position and fit headrest guides in squab 
assembly.
3.Position and fit seat fold release button 
escutcheon.
4.Secure squab cover beading to sides and 
bottom of frame.
5.Fit rear squab finisher.
 
 +  SEATS, REPAIRS, Finisher - rear 
seat squab.
6.Position squab frame to seat frame and secure 
LH side with Torx bolt, tighten to 25 Nm (18 
lbf.ft)....

SEATS
REPAIRS 76-5-39
5.Remove and discard Torx bolt securing seat 
belt stalk, remove stalk.
Refit
1.Position seat belt stalk and secure with Torx 
bolt, tighten to 31 Nm (23 lbf.ft).
2.Position mechanism to seat frame and secure 
with Allen bolts, tighten to 25 Nm (18 lbf.ft). 
3.Position squab frame to mechanism and 
secure with Torx bolts, tighten to 25 Nm (18 
lbf.ft).
4.Position mechanism finisher and secure with 
screws.
5.Reposition rear seat. 

SEATS
76-5-40 REPAIRS 

SUNROOF
ADJUSTMENT 76-6-1
SUNROOF ADJUST ME NT
Sun roof - align to roof panel & adjust 
$% 76.84.82
Check
1.With sunroof closed, check alignment of glass 
to roof panel. The glass should be central in its 
aperture. Profile of sunroof to body:
lfront edge of sunroof = flush or up to 1.0 mm 
(0.040 in) lower
lrear edge of sunroof = flush or up to 1.0 mm 
(0.040 in) higher
Adjust
1.Open sunroof blind.
2.Operate switch to raise sunroof fully.
3.Carefully release upper edges of gaiters from 
sunroof glass....