Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

INTERIOR FITTINGS
76-3-36 REPAIRS
12.Fit B post upper finishers.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - B post - upper.
13.Fit A post upper finishers.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - A post - upper.
14.Fit rear seat.
 
 +  SEATS, REPAIRS, Rear seat.
15. Models fitted with sunshine roof: Close 
sunshine roof.
16.Connect battery earth lead. 

SCREENS
REPAIRS 76-4-1
SCREENS REPAIRS
Glass - tailgate upper
$% 76.31.22 
The following equipment is required:
lCutting wire and handles
lGlazing knife
lGlass replacement kit
lSealant applicator gun
lSuction cups
lA felt covered table or stand to support glass
Remove
1.Remove rear wiper arm.
 
 +  WIPERS AND WASHERS, REPAIRS, 
Arm - wiper - tailgate.
2.Remove tailgate trim casing.
 
 +  DOORS, REPAIRS, Trim casing - 
tailgate upper.
3.Remove tailgate inner side finishers.
4.Remove tailgate glass outer...

SCREENS
76-4-2 REPAIRS
Refit
1.Carefully remove sealant from body to leave a 
smooth surface.
2. Original screen: Carefully cut back sealant to 
obtain a smooth surface without damage to 
obscuration band
3.Fit finisher to screen.
4.Fit support blocks to body.
5.Fit screen to body and centralise in aperture.
6.Use masking tape to establish reference marks 
as an alignment aid.
7.Remove windscreen and place on stand.
8.Clean sealant face on body and windscreen 
with solvent.
9.Apply etch primer to any...

SCREENS
REPAIRS 76-4-3
Windscreen
$% 76.81.01 
The following equipment is required:
lCutting wire and handles
lKent knife
lGlazing knife
lWindscreen replacement kit
lSealant applicator gun
lSuction cups
lA felt covered table or stand to support glass
Remove
1.Remove roof finishers.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Roof moulding.
WARNING: Wear protective gloves when 
handling glass, solvents and primers.
2.Remove windscreen side finishers.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Side finisher - windscreen....

SCREENS
76-4-4 REPAIRS
12.From outside of vehicle, use a Kent knife and 
carefully cut through sealant securing upper 
and both sides of windscreen to body.
13.If necessary, use cutting wire to cut through any 
remaining sealant securing top and sides of 
windscreen.
14.From inside vehicle, carefully cut through 
sealant securing lower edge of windscreen with 
a glazing knife. It is not practical to use a Kent 
knife as the windscreen is very close to body.
15.Attach suction cups and with assistance,...

SCREENS
REPAIRS 76-4-5
13.Fit pre-cut nozzle to sealer cartridge, remove 
lid, shake out crystals and fit cartridge to 
applicator gun. If necessary modify the nozzle 
to achieve required bead section.
14.Apply a continuous bead of sealant to 
windscreen as shown.
15.With assistance, fit and align windscreen. 
Lightly press windscreen to seat sealer.
16.Remove protective covers and tape.
17.Test sealer for leaks, apply additional sealer if 
necessary. If water is used, allow sealer to dry 
before...

SCREENS
76-4-6 REPAIRS
Glass - quarter light - rear
$% 76.81.20 
The following equipment is required:
lCutting wire and handles
lKent knife
lGlass replacement kit
lSealant applicator gun
lA felt covered table or stand to support glass
Remove
1.Remove E post finisher.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Finisher - E post.
2.Remove quarter light front finisher.
3.Remove rear quarter trim access panel
4.Disconnect receiver multiplug from glass.
5.Protect exterior body work adjacent to quarter 
light....

SCREENS
REPAIRS 76-4-7
8.Apply a continuous bead of sealant to quarter 
light as shown.
9.Fit and align quarter light to body. Lightly press 
on glass to seat sealer.
10.Connect receiver multiplug.
11.Fit rear quarter trim access panel
12.Remove protective covers and tape.
13.Test sealer for leaks, apply additional sealer if 
necessary. If water is used, allow sealer to dry 
before testing. Spray water around glass and 
check for leaks. Mark any area that leaks. Dry 
glass and sealer then apply...

SCREENS
76-4-8 REPAIRS 

SEATS
REPAIRS 76-5-1
SEATS REPAIRS
Arm rest - rear seat 
$% 78.10.07.99
Remove
1.Remove rear seat hinge.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
2.Release centre catch and fold armrest down.
3.Release velcro strip securing armrest cover to 
back of squab, fold cover down.
4.Remove Torx bolt from armrest pivot point.
5.Release armrest assembly from LH pivot point 
boss, remove assembly.Refit
1.Position and fit armrest assembly to pivot point 
boss.
2.Fit and tighten Torx bolt to secure armrest to...