Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

INTERIOR FITTINGS
76-3-26 REPAIRS
52.Disconnect headlamp multiplug.
53.Note fitted position of ride height sensor cable 
ties, remove cable ties and disconnect 
multiplug.
54.Disconnect multiplugs from radiator pack.55.Disconnect multiplug from ABS sensor.
56.Disconnect multiplug from A/C switch.
57.Disconnect multiplug from A/C compressor.
M76 4426
M70 1128
M76 4427
M76 4428 

INTERIOR FITTINGS
REPAIRS 76-3-27
58.Disconnect multiplug from PAS rack pinion 
sensor.
59.Remove screw securing light check control 
module to A post.
60.Move light check module aside.
61.Remove bolt securing door harness connector 
block to A post and disconnect multiplug.62. Remove nut securing earth header to A post 
and release header.
63.Raise carpet and remove 3 scrivets securing 
harness closing panel to body, release and 
remove panel.
64.Release clips securing harness connector 
block to BCU...

INTERIOR FITTINGS
76-3-28 REPAIRS
65.Remove 2 nuts and move BCU carrier aside.
66.Release main harness from channel and 
reposition carpet.
67.With assistance, withdraw harness through 
bulkhead and rotate fascia assembly for 
access.
CAUTION: Ensure evaporator drain tubes 
are not damaged when moving fascia.
68.Support fascia on suitably protected axle 
stands avoiding damage to carpet and trim.
Refit
1.With assistance position harness and fascia 
assembly to bulkhead.
2.Connect airbag and A post...

INTERIOR FITTINGS
REPAIRS 76-3-29
43.Fit lower A post finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - A post - lower.
44.Fit drivers footrest.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Foot rest finisher - LHD.
45.Fit and secure ducts to heater assembly.
46.Fit centre console closing panel.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - centre console.
47.Fit handbrake lever assembly.
 
 +  BRAKES, REPAIRS, Lever assembly 
- handbrake.
48.Fit air suspension switch panel.
 
 +  INTERIOR...

INTERIOR FITTINGS
76-3-30 REPAIRS
Closing panel - drivers side  
$% 76.46.28
Remove
1.Remove closing panel from drivers side of the 
centre console.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - centre console.
2.Remove 4 screws and 1 trim stud securing 
closing panel.
3.Release closing panel, disconnect multiplugs 
from sounder and footwell lamp assembly, 
remove panel.
4.Remove sounder, lamp and speed nut from 
panel.
Refit
1.Fit sounder, lamp and speed nut to panel.
2.Position panel, connect...

INTERIOR FITTINGS
REPAIRS 76-3-31
Retainer - front carpet 
$% 76.49.17 
This procedure is also applicable to the rear carpet 
retainer.
Remove
1.Using a trim removal tool, release 7 clips 
securing treadplate carpet retainer to sill.
2.Remove treadplate.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
3.Remove 4 clips from treadplate.
Refit
1.Fit clips to treadplate.
2.Position and secure treadplate to sill.
Finisher - tailgate carpet 
$% 76.49.23
Remove
1.Remove...

INTERIOR FITTINGS
76-3-32 REPAIRS
Glove box 
$% 76.52.03
Remove
1.Remove upper finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - upper - drivers side.
2.Remove lower finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - lower - passengers side.
3.Remove 2 Torx screws securing glove box from 
underside of fascia.
4.Open glove box.
5.Remove 5 Torx screws securing glove box.
6.Disconnect multiplug from lamp.
7.Release cable from glove box latch.8. If fitted: Remove 2 Torx screws securing CD...

INTERIOR FITTINGS
REPAIRS 76-3-33
Refit
1.Position latch and fixing plate to glove box, 
secure with screws.
2.Fit lamp assembly to glove box.
3.Fit fuse box cover.
4.Fit clips to glove box.
5.Fit fuse puller.
6.Position glove box to fascia.
7. If fitted: Position CD multi-changer to glove 
box, connect link lead and multiplugs.
8. If fitted: Fit CD multi-changer to glove box and 
secure with Torx screws.
9.Connect cable to glove box latch.
10.Connect multiplug to lamp assembly.
11.Secure glove box with...

INTERIOR FITTINGS
76-3-34 REPAIRS
Handle - grab 
$% 76.58.30
Remove
1.Release covers from grab handle retaining 
screws.
2.Remove 2 screws securing grab handle and 
remove handle.
3.Remove grab handle support plate.
Refit
1.Fit grab handle support plate.
2.Fit grab handle and secure with screws.
3.Fit screw covers.
Headlining 
$% 76.64.15 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical...

INTERIOR FITTINGS
REPAIRS 76-3-35
11.Remove rear console from headlining.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Console - headlining - rear.
12.Remove grab handles.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Handle - grab.
13.Open flap, remove 4 screws securing cargo net 
upper anchor finishers and remove finishers.
14.Remove seals from door aperture flanges to 
release headlining.
15.Remove 2 screws securing headlining.
16. Models fitted with sunshine roof: Remove 4 
screws securing headlining.17.Carefully release...