Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

DOORS
76-1-16 REPAIRS
Finisher - upper - tailgate lower  
$% 76.34.44
Remove
1.Open upper and lower tailgates.
2.Remove 6 screw caps.
3.Remove 6 screws securing trim finisher.
4.Remove trim finisher.
Refit
1.Fit trim finisher and secure with screws.
2.Fit screw covers.
Latch - front door 
$% 76.37.12 
This procedure is also applicable to the rear door 
latch.
Remove
1.Ensure window is fully raised.
2.Remove plastic sheet.
 
 +  DOORS, REPAIRS, Plastic sheet - 
front door.
 
 +  DOORS, REPAIRS, Plastic...

DOORS
REPAIRS 76-1-17
10.Remove internal release cable and latch as an 
assembly.
11.Open security flap on latch.
12.Release interior release cable clamp from 
latch.
13.Disengage interior release cable from latch.
14.Remove cable.
Refit
1.Secure interior release cable to latch and close 
latch security flap.
2.Position latch to door. On drivers door, align 
lock barrel paddle to latch.
3.Position door latch fit Torx screws and tighten 
to 10 Nm (7 lbf.ft).
4.Connect outer release cable to latch...

DOORS
76-1-18 REPAIRS
Refit
1.Position support bracket to latch, fit bolts and 
tighten to 10 Nm (7 lbf.ft).
2.Connect manual release cable.
3.Position latch assembly to tailgate and connect 
multiplug.
4.Fit bolts to latch and tighten to 10 Nm (7 lbf.ft).
5.Fit tailgate trim casing.
 
 +  DOORS, REPAIRS, Trim casing - 
tailgate upper.
6.Adjust tailgate striker.
 
 +  DOORS, ADJUSTMENTS, Tailgate 
lower - adjust on striker.
Latch - outer - tailgate 
$% 76.37.83
Remove
1.Open upper and lower tailgates....

DOORS
REPAIRS 76-1-19
Finisher - front door 
$% 76.42.05
Remove
1.Carefully release 12 clips securing finisher to 
door.
CAUTION: Always protect paintwork when 
removing or refitting any body trims or 
bumpers.
2.Remove door finisher.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
3.Remove clips from door finisher.
4.Remove seal from door finisher.
Refit
1.Fit seal to finisher.
2.Fit clips to door finisher.
3.Fit and secure door finisher.
Finisher - rear door 
$%...

DOORS
76-1-20 REPAIRS
Handle - outside - front door 
$% 76.58.07 
This procedure is also applicable to the rear door 
handle.
Remove
1.Remove plastic sheet.
 
 +  DOORS, REPAIRS, Plastic sheet - 
front door.
 
 +  DOORS, REPAIRS, Plastic sheet - 
rear door.
2. Drivers door: Remove grommet for access to 
lock retaining screw.
3. Drivers door: Remove Torx screw securing 
lock and remove lock assembly.
4.Remove Torx screw securing door handle 
assembly.
5.Release handle assembly from door.6.Disconnect...

EXTERIOR FITTINGS
REPAIRS 76-2-1
EXTERIOR FITTINGS REPAIRS
Panel - extension - front wing 
$% 76.10.03
Remove
1.Remove 9 screws securing rear of wheelarch 
liner to inner wing and sill, release liner from 
wing for access.2.Remove scrivet securing front wing extension 
panel to lower wing.
3.Release and remove the lower front wing 
extension from retaining clips.
4.Release and remove the sill seal from the front 
wing extension panel.
NOTE: Do not carry out further dismantling if 
component is removed...

EXTERIOR FITTINGS
76-2-2 REPAIRS
Wing - front 
$% 76.10.24
Remove
1.Secure bonnet in service position.
2.Remove front wing grille.
3.Remove front indicator lamp assembly.
 
 +  LIGHTING, REPAIRS, Lamp 
assembly - side & indicator.
4.Mark fitted position of front wing relative to 
body.
5.Remove 8 bolts securing front wing panel to 
inner wing and A post.
6.Collect 2 nylon spacers from the front vertical 
mountings.
7.Remove side repeater lamp from front wing.
 
 +  LIGHTING, REPAIRS, Lamp 
assembly -...

EXTERIOR FITTINGS
REPAIRS 76-2-3
8.Fit side repeater lamp to front wing.
 
 +  LIGHTING, REPAIRS, Lamp 
assembly - indicator side repeater.
9.Secure bonnet struts.Liner - front wheel arch  
$% 76.10.48
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a 
vehicle supported only by a jack. Always 
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove 3 plastic nuts securing inner wheel 
arch liner.
4.Remove 11 hexagonal headed screws 
securing wheel arch liner.
5.Remove 2...

EXTERIOR FITTINGS
76-2-4 REPAIRS
Liner - rear wheel arch - single 
$% 76.10.49
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a 
vehicle supported only by a jack. Always 
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove 2 scrivets securing wheel arch liner to 
sill and bumper.
4.Remove 3 plastic nuts securing inner wheel 
arch liner.
5.Remove 4 hexagonal headed screws securing 
wheel arch liner.
6.Release and remove wheel arch liner.
Refit
1.Position wheel arch liner...

EXTERIOR FITTINGS
REPAIRS 76-2-5
Mirror glass - exterior
$% 76.11.08
Remove
1.Using fingers, gently press lower edge of mirror 
glass inboard to maximum rotation.
2.Position 2 levers to lower edge of mirror glass 
surround, apply vertical leverage.
WARNING: Wear suitable eye protection 
when removing and refitting glass.
3.Continue to apply an even but constant 
pressure, until glass releases from mounting.
4.Disconnect 2 Lucar connections from Mirror 
glass and remove.
Refit
1.Connect Lucars to mirror...