Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

INTERIOR FITTINGS
76-3-6 REPAIRS
Trim finisher - E post  
$% 76.13.32
Remove
1.Open tailgate.
2.Release aperture seal.
3.Release 4 fixings securing E post finisher and 
carefully remove finisher.
4.Remove fixings from finisher.
Refit
1.Fit new fixings to finisher.
2.Fit finisher and secure fixings.
3.Fit seal to aperture.
Centre console
$% 76.25.01
Remove
1.Remove centre console finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - console.
2.Remove both centre console closing panels.
 
 +  INTERIOR...

INTERIOR FITTINGS
REPAIRS 76-3-7
6.Remove 2 Torx screws and collect washers 
from base of large cubby box.
7.Remove 2 screws securing centre console rear 
closing panel. Release clips and remove panel.
8.Raise rear of centre console, disconnect 3 
multiplugs from centre console and collect air 
duct adaptor.
9.Disconnect 3 Lucar connectors from accessory 
power socket.10.Carefully remove centre console.
CAUTION: Care must be taken to protect 
painted and veneered surfaces.
Refit
1.Position centre console...

INTERIOR FITTINGS
76-3-8 REPAIRS
Console - headlining - front  
$% 76.25.02
Remove
1.Open spectacle holder, remove 2 screws 
securing console and release console from 
headlining.
2.Disconnect multiplugs from switches and lamp. 
Remove console assembly.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
3.Remove lamp from console.
4.Remove switches from console.
5.Remove 2 retaining clips from console.Refit
1.Fit retaining clips to console.
2.Fit switches to console....

INTERIOR FITTINGS
REPAIRS 76-3-9
Finisher - console  
$% 76.25.07
Remove
1.Remove gear selector cover.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Cover - automatic transmission selector.
2.Release gaiter from handbrake lever grip.
3.Release and remove handbrake lever grip.
4.Open cubby box lids, carefully release clips and 
remove finisher.
5.Remove 6 Torx screws securing finisher to 
centre console, fully apply handbrake.
6.Release finisher from clips, raise and 
disconnect 3 Lucar connectors from accessory...

INTERIOR FITTINGS
76-3-10 REPAIRS
5.Position centre console finisher and connect 
Lucars.
6.Connect multiplug to closing panel lamp 
assembly.
7.Fit finisher and secure with Torx screws.
8.Fit handbrake lever grip and secure gaiter.
9.Fit and secure small cubby box finisher.
10.Close cubby box lids.
11.Fit gear selector cover.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Cover - automatic transmission selector.
Console - headlining - rear 
$% 76.25.08
Remove
1.Carefully release rear console from headlining....

INTERIOR FITTINGS
REPAIRS 76-3-11
Cover - automatic transmission selector 
$% 76.25.09
Remove
1.Turn ignition key to position II, depress brake 
pedal and move gear lever to D drive, turn 
ignition off.
2.Release clips and gear selector cover from 
centre console.
3.Carefully disconnect 4 multiplugs from gear 
selector panel.
4.Remove gear lever knob and cover by pulling 
sharply upward.
5.Release clips securing gear lever gaiter to 
centre console cover, remove knob and gaiter.
Refit
1.Position cover...

INTERIOR FITTINGS
76-3-12 REPAIRS
Switch panel - air suspension  
$% 76.25.41
Remove
1.Remove heating control assembly.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Controls - heater (ECU).
2.Carefully release clips securing air suspension 
switch panel, disconnect multiplug and remove 
the panel.
Refit
1.Position air suspension switch panel, connect 
multiplug and secure panel to carrier.
2.Fit heating control assembly.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Controls - heater (ECU).
Top rail - fascia 
$%...

INTERIOR FITTINGS
REPAIRS 76-3-13
7.Remove 4 Torx screws securing instrument 
pack finisher, remove finisher.
Refit
1.Fit instrument pack finisher to top rail and 
secure with Torx screws.
2.Fit speaker and secure with screws.
3.Position top rail, connect speaker multiplug. 
Secure rail with Torx screws.
4.Position and secure centre grille.
5.Fit drivers side upper trim finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - upper - drivers side.
6.Fit passenger side upper finisher.
 
 +  INTERIOR...

INTERIOR FITTINGS
76-3-14 REPAIRS
3.Position shroud to carrier, fit and secure with 
clips and screws.
4.Fit drivers side lower trim finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - lower - drivers side.
5.Fit drivers side upper trim finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - upper - drivers side.
6.Fit centre air vent.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Ventilator(s) - centre.
7.Fit glove box.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Glove box.
8.Fit rotary coupler.
 
 +  RESTRAINT...

INTERIOR FITTINGS
REPAIRS 76-3-15
Finisher - upper - drivers side 
$% 76.46.12
Remove
1.Remove fascia end closing panel.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Closing panel - fascia end.
2.Remove face level air vent.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Fresh air vent - face level.
3.Remove A post upper trim finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - A post - upper.
4.Remove 3 Torx screws securing upper finisher 
to fascia.
5.Release upper finisher from fascia and 
disconnect switch...