Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

EXTERIOR FITTINGS
76-2-6 REPAIRS
Refit
1.Fit harness, position motor and secure with 
screws.
2.Feed harness through cheater casting, fit Torx 
screws and tighten to 14 Nm (10 lbf.ft).
3.Fit and secure access cover.
4.Align harness and secure with star washer.
5.Fit locking body to multiplug.
6.Fit exterior mirror.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Mirror - exterior.
7.Fit exterior mirror glass.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Mirror - exterior.
Mirror - exterior
$% 76.11.10
Remove
1.Remove front...

EXTERIOR FITTINGS
REPAIRS 76-2-7
Refit
1.Fit foam pad to cheater panel.
2.Feed mirror harness through panel, position 
mirror, fit and tighten Torx screws to 10 Nm (7 
lbf.ft).
3.Fit and secure upper door trim finisher.
4.Fit front door trim casing.
 
 +  DOORS, REPAIRS, Trim casing - 
front door.
Tow bar 
$% 76.11.41
Remove
1.Remove bumper armature.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Bumper armature - rear.
2.Remove tow ball locking pin.
3.Remove nut and bolt securing tow ball to tow 
bar. Remove the...

EXTERIOR FITTINGS
76-2-8 REPAIRS
5.Remove 4 nuts securing exhaust rubber 
mountings to the rear subframe.
6.Support exhaust and remove 4 nuts securing 
exhaust rubber mountings to the tow bar.
7.Lower exhaust sufficiently to allow access to 
tow bar retaining bolts.
8.Remove 4 bolts securing tow bar to body and 
with assistance remove the tow bar.
Refit
1.With assistance position tow bar to body, fit 
bolts and tighten to 165 Nm ( 122 lbf.ft).
2.Position socket to tow bar, fit bolts and tighten 
to 25 Nm...

EXTERIOR FITTINGS
REPAIRS 76-2-9
6.Remove 2 screws securing LH inner edge of 
wheel arch liner to undertray, repeat on RH 
side.
7.Remove 6 remaining screws securing 
undertray, release panel and remove.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
8.Remove 6 screw retaining clips from undertray.
Refit
1.Fit screw retaining clips to undertray.
2.Position undertray and secure with screws.
3.Fit screws securing air dam and wheelarch 
liners.
4.Fit and secure towing...

EXTERIOR FITTINGS
76-2-10 REPAIRS
8.Remove stud and turn buckle securing lower 
rear quarter trim on LH and RH side of vehicle.
9.Remove warning triangle.
10.Release clip and remove wheel chock and tool 
roll.
11.Remove RH bin from loadspace carrier.
12.Remove 3 plastic nuts and release 2 studs 
securing RH bin carrier, remove carrier.
13.Remove 3 plastic nuts securing LH carrier and 
remove carrier.14.Remove 8 nuts securing rear armature and 
remove.
NOTE: Do not carry out further dismantling if...

EXTERIOR FITTINGS
REPAIRS 76-2-11
13.Fit rear bumper.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Bumper - rear.
14.Close both tail gates.Bumper - assembly - front   
$% 76.22.72
Remove
1.Remove front grille.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Front grille.
2.Remove screw securing wheel arch liner to 
bumper, repeat procedure on opposite side.
3.Release clips and remove towing eye finisher.
4.Remove 6 screws securing bumper valance to 
undertray.
5.Remove 2 screws securing bumper to 
armature. 

EXTERIOR FITTINGS
76-2-12 REPAIRS
6.Remove 4 screws securing bumper to armature 
extension.
7.With assistance carefully lift and pull forward 
each side of bumper to release bumper side 
mounts and clips.
CAUTION: Always protect paintwork when 
removing or refitting any body trims or 
bumpers.
8.Disconnect multiplugs from fog lamps.
9. Vehicles fitted with parking sensors: 
Disconnect 4 multiplugs.
10.Remove front bumper.
NOTE: Do not carry out further dismantling if 
component is removed for access...

EXTERIOR FITTINGS
REPAIRS 76-2-13
10.Ensure bumper locating pegs are correctly 
aligned.
11.Fit and tighten screws securing bumper to 
bumper armature and undertray.
12.Fit and tighten screws securing wheel arch 
liners to bumper valance and undertray.
13.Fit and secure towing eye finisher.
14.Fit front grille.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Front grille.
Bumper - rear  
$% 76.22.74
Remove
1.Remove 2 scrivets and 4 screws securing 
wheel arch liner to rear bumper.
2.Remove 5 screws securing bumper...

EXTERIOR FITTINGS
76-2-14 REPAIRS
3.Carefully release 7 clips securing rear bumper 
finisher, open lower tailgate and remove 
finisher.
4.Remove 5 screws securing top edge of bumper 
to armature.
5.Depress 6 clips securing bumper to rear wings 
and with assistance remove bumper from 
vehicle.
CAUTION: Always protect paintwork when 
removing or refitting any body trims or 
bumpers.
Refit
1.With assistance position bumper to body.
2.Fit and finger tighten screws securing top edge 
of bumper to armature....

EXTERIOR FITTINGS
REPAIRS 76-2-15
3.Remove 3 screws securing bumper extension 
to undertray.
4.Remove screw securing extension to bumper.
5.Release extension from wheel arch liner, 
release clips and remove from bumper.
Refit
1.Fit screws and secure bumper extension to 
front bumper.
2.Fit and tighten screw securing bumper 
extension to wheel arch liner.
3.Fit and secure towing eye finisher.
Finisher - sill 
$% 76.43.28
Remove
1.Remove 8 scrivets from underside of sill 
finisher.
2.Carefully release 10...