Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

RESTRAINT SYSTEMS
75-36 REPAIRS
15.Transport deployed airbag module to 
designated area for incineration.
CAUTION: Do not re-use or salvage any 
parts of the SRS system.
NOTE: Do not transport deployed SRS 
components in the vehicle passenger 
compartment.
Airbag module - head - rear - deployment 
- in vehicle
$% 76.74.44 
These guidelines are written to aid authorised 
personnel to carry out the safe disposal of airbag 
modules. 
Deploy
WARNING: It is imperative that before any 
work is undertaken on...

RESTRAINT SYSTEMS
REPAIRS 75-37
6.Connect deployment tool LRT-86-003 to 
deployment tool fly lead LRT-86-003/08.
7.Connect deployment tool LRT-86-003 to 
battery.
WARNING: Ensure all personnel are at least 
15 metres (50 feet) away from the airbag 
module.
8.Press deployment tool operating button to 
deploy airbag module.
9.Disconnect deployment tool from battery.
WARNING: During deployment parts of the 
airbag module become hot enough to burn 
you. Wait 30 minutes after deployment 
before touching the...

RESTRAINT SYSTEMS
75-38 REPAIRS
4.Position LRT-86-007/02 in vice, ensuring that 
vice jaws grip tool above the bottom flange to 
prevent possibility of tool being forced upwards 
during detonation. Tighten vice.
5.Fit and secure 2 off LRT-86-007/05 to LRT-86-
007/02.
6.Fit and secure airbag to LRT-86-007/05.7.Connect deployment tool fly lead LRT-86-003/
08 to airbag.
8.Connect deployment tool LRT-86-003 to 
deployment tool fly lead LRT-86-003/08.
9.Connect deployment tool LRT-86-003 to 
battery.
WARNING:...

RESTRAINT SYSTEMS
REPAIRS 75-39
15.Transport deployed airbag module to 
designated area for incineration.
CAUTION: Do not re-use or salvage any 
parts of the SRS system.
NOTE: Do not transport deployed SRS 
components in the vehicle passenger 
compartment. 

RESTRAINT SYSTEMS
75-40 REPAIRS 

DOORS
ADJUSTMENTS 76-1-1
DOORS ADJUST ME NTS
Tailgate lower - adjust on striker
$% 76.28.03
Check
1.Check for equal gap and alignment to adjacent 
panels. If incorrect follow adjust procedure 
below.
Adjust
1.Open tailgate.
2.Loosen 2 bolts securing lower tailgate striker.
3.Close tailgate, check for equal gap and 
alignment to adjacent panels.
4.Open lower tailgate and tighten bolts securing 
striker to 25 Nm (18 lbf.ft).
5.Close tailgate.
Tailgate upper - adjust on striker(s)
$% 76.28.28
Adjust
1.Open...

DOORS
76-1-2 ADJUSTMENTS 

DOORS
REPAIRS 76-1-3
REPAIRS
Glass - front door 
$% 76.31.01
Remove
1.Lower door glass.
2.Remove plastic sheet.
 
 +  DOORS, REPAIRS, Plastic sheet - 
front door.
3.Loosen two Torx bolts securing glass to 
regulator.
4.Remove glass.
Refit
1.Position glass to regulator.
2.Lightly tighten Torx bolts.
3.Raise regulator, check glass alignment, adjust 
as necessary.
4.Tighten Torx bolts securing front glass to 10 
Nm (7 lbf.ft).
5.Fit plastic sheet.
 
 +  DOORS, REPAIRS, Plastic sheet - 
front door.
Glass -...

DOORS
76-1-4 REPAIRS
6.Remove Torx bolt securing glass to regulator.
7.Remove glass.
Refit
1.Position glass to regulator, fit bolt and tighten to 
10 Nm (7 lbf.ft).
2.Fit glass channel to frame and secure with 
screws.
3.Fit and secure seal.
4.Connect multiplug, fit and secure upper 
finisher.
5.Fit plastic sheet.
 
 +  DOORS, REPAIRS, Plastic sheet - 
rear door.
6.Raise and lower glass to check operation.
Quarter light - fixed - rear door 
$% 76.31.31
Remove
1.Remove rear door glass.
 
 +  DOORS,...

DOORS
REPAIRS 76-1-5
5.Remove outer waist seal.
6.Remove inner waist seal.
7.Remove quarter light outer trim.
8.Use a Kent knife and carefully cut through 
sealant securing glass to door frame.
9.Remove quarter light.
Refit
1.Carefully remove sealant from door frame to 
leave a smooth surface.2. Original quarter light: Carefully cut back 
sealant to obtain a smooth surface without 
damage to obscuration band.
3.Clean sealant face on door frame and quarter 
light with solvent.
4.Apply etch primer to any...