Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

BRAKES
70-24 REPAIRS
7.Release catch and disconnect ABS modulator 
multiplug.
8.Remove 6 Torx screws securing ABS ECU.
CAUTION: Before disconnecting or 
removing components, ensure the 
immediate area around joint faces and 
connections are clean. Plug open 
connections to prevent contamination.
9.Remove ABS ECU.
CAUTION: Do not touch the exposed 
modulator solenoids as this could lead to 
solenoid damage.
Refit
1.Ensure ABS ECU and modulator mating faces 
are clean.
2.Fit ABS ECU to modulator, fit Torx...

BRAKES
REPAIRS 70-25
5.Release sensor lead from damper, remove 
Allen screw and release ABS sensor from hub.
Refit
1.Clean ABS sensor, smear sensor with an anti-
seize grease and fit sensor to hub.
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, 
Lubrication.
2.Fit Allen screw securing ABS sensor and 
tighten to 8 Nm (6 lbf.ft).
3.Secure sensor lead to damper, brake hose 
bracket, clip and body bracket then connect 
and secure multiplug. Close cover on multiplug 
housing.
4.Fit road wheel and tighten...

BRAKES
70-26 REPAIRS
Refit
1.Clean ABS sensor, smear sensor with an anti-
seize grease and fit sensor to hub.
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, 
Lubrication.
2.Fit Allen screw securing ABS sensor and 
tighten to 8 Nm (6 lbf.ft).
3.Secure sensor lead to suspension arm and 
suspension turret then connect and secure 
multiplug. Close cover on multiplug housing.
4.Locate wheel arch liner and secure with 
screws.
5.Fit road wheel and tighten nuts to 140 Nm (103 
lbf.ft).
6.Remove stand and...

BRAKES
REPAIRS 70-27
Refit
1.Position mounting bracket to modulator, fit bolts 
and tighten to 8 Nm (6 lbf.ft).
2.Position modulator to mounting bracket, fit bolt 
and tighten to 8 Nm (6 lbf.ft).
3.Clean brake pipe unions.
4.Connect brake pipe unions to ABS modulator 
ensuring pipes are connected to their correct 
ports.
5.Tighten ABS modulator brake pipe unions to 18 
Nm (13 lbf.ft).
6.Connect multiplug to sensor.
7.Connect ABS modulator multiplug and secure 
catch.
8.Bleed brakes.
9.To ensure correct...

BRAKES
70-28 REPAIRS
Sensor - dynamic stability control (DSC) 
$% 70.70.35
Remove
1.Remove centre console finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Finisher - console.
2.Release and remove air duct.
3.Remove 2 bolts securing DSC sensor.
4.Release DSC sensor, disconnect multiplug and 
remove sensor.
Refit
1.Position DSC sensor and connect multiplug.
2.Locate DSC sensor to mounting bracket, fit 
bolts and tighten to 8 Nm (6 lbf.ft).
3.Fit air duct.
4.Fit centre console finisher.
 
 +  INTERIOR FITTINGS,...

RESTRAINT SYSTEMS
REPAIRS 75-1
RESTRAINT SYSTEMS REPAIRS
Seat belt - front 
$% 76.73.13 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
WARNING: Always disconnect both battery leads 
before beginning work on the SRS system. 
Disconnect the negative lead first. Never reverse 
connect the battery.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint...

RESTRAINT SYSTEMS
75-2 REPAIRS
Seat belt - centre - rear 
$% 76.73.20
Remove
1.Remove seat base finisher.
 
 +  SEATS, REPAIRS, Finisher - seat 
base rear.
2.Remove seat fold mechanism.
 
 +  SEATS, REPAIRS, Hinge - rear seat 
- side.
3.Remove Torx bolt securing squab frame to seat 
frame and separate frames.
4.Disconnect multiplug from heated squab cover.
5.Release seat cover beading from sides and 
front of seat.6.Raise seat cover and cushion, remove and 
discard Torx bolt securing seat belt anchor...

RESTRAINT SYSTEMS
REPAIRS 75-3
13.Raise squab cover and cushion to gain access 
to headrest guides.
14.Release 3 clips securing headrest guides to 
frame, remove guides.
15.Remove cover and cushion assembly from 
frame and feed seat belt through assembly.
16.Remove and discard Torx bolt securing seat 
belt reel to squab frame, remove reel.
Refit
1.Position seat belt reel and secure with Torx bolt 
and tighten to 48 Nm (35 lbf.ft).
2.Feed seat belt through cover and cushion 
assembly and fit assembly to...

RESTRAINT SYSTEMS
75-4 REPAIRS
Seat belt - rear 
$% 76.73.23
Remove
1.Remove D post lower trim.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - lower.
2.Remove Torx bolt securing seat belt floor 
anchor and remove D post upper trim.
3.Remove Torx nut securing seat belt to upper D 
post anchor.
4.Remove Torx bolt securing seat belt reel.
5.Release seat belt reel from alignment bracket 
and remove reel.Refit
1.Fit seat belt reel to alignment bracket.
2.Fit Torx bolt securing seat belt reel and...

RESTRAINT SYSTEMS
REPAIRS 75-5
Pre-tensioner - front seat belt
$% 76.73.75 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
WARNING: Always disconnect both battery leads 
before beginning work on the SRS system. 
Disconnect the negative lead first. Never reverse 
connect the battery.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS)...