Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

REAR SUSPENSION
64-12 REPAIRS
9.Remove bolt securing damper to lower arm.
10.Remove damper.
11.Remove and discard gasket.
12.Restrain damper spindle and remove nut 
securing upper mounting.
13.Remove washer, upper mounting, dust cover, 
support disc and bump stop.
Refit
1.Fit bump stop, support disc, dust cover, upper 
mounting and washer to damper.
CAUTION: The support disc is hardened 
and must be fitted in the correct position.
2.Fit nut, restrain damper spindle and tighten nut 
to 27 Nm (20 lbf.ft)....

REAR SUSPENSION
REPAIRS 64-13
Anti-roll bar 
$% 64.35.08 
Do not depressurise air suspension system before 
raising vehicle
Remove
1.Remove exhaust system.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- Td6, REPAIR, Exhaust system and 
mountings.
2.Remove nuts securing anti-roll bar links and 
release both links from anti-roll bar.
CAUTION: Use an open ended spanner on 
flats provided to prevent ball joint rotating.
3.Collect washer from lower fixing.
CAUTION: Note position of washer for refit.
4.Remove 4 bolts...

REAR SUSPENSION
64-14 REPAIRS
Tie rod 
$% 64.35.09
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a 
vehicle supported only by a jack. Always 
support the vehicle on safety stands.
2.Remove road wheel.
3.Restrain ball pin and remove nut securing tie 
rod to hub.
4.Remove nut and bolt securing sensor link to 
lower arm.5.Reference mark eccentric in relationship to 
subframe.
6.Remove bolt securing tie rod to subframe. 
Discard bolt.
7.Collect special washer.
8.Remove tie rod.
Refit...

REAR SUSPENSION
REPAIRS 64-15
Bushes - upper arm 
$% 64.35.13
Remove
1.Remove upper arm.
 
 +  REAR SUSPENSION, REPAIRS, Arm 
assembly - upper.
2.Secure upper arm in a soft jawed vice.
3.Remove bushes using LRT-64-024/1 with  
LRT-64-024/2 and LRT-64-024/3.Refit
1.Align bushes as shown and fit using LRT-64-
024/1 with  LRT-64-024/4 and LRT-64-024/5.
2.Remove upper arm from vice.
3.Fit upper arm.
 
 +  REAR SUSPENSION, REPAIRS, Arm 
assembly - upper. 

REAR SUSPENSION
64-16 REPAIRS
Bushes - lower arm - front 
$% 64.35.16 
The bushes must be replaced as a pair, LH and RH 
sides.
Remove
1.Remove lower arms.
 
 +  REAR SUSPENSION, REPAIRS, Arm 
assembly - lower.
2.Remove bush using LRT-64-027/1 with LRT-
64-027/2 and LRT-64-027/3 in direction shown.
3.Repeat procedure for other side.
Refit
1.Ensure bush and bush location in lower arm is 
clean.
2.Fit bush using LRT-64-027/1 with LRT-64-027/
2 and LRT-64-027/3 in  position and direction 
shown.3.Check...

REAR SUSPENSION
REPAIRS 64-17
Bushes - lower arm - rear 
$% 64.35.17 
The bushes must be replaced as a pair, LH and RH 
sides. 
Remove
1.Remove lower arms.
 
 +  REAR SUSPENSION, REPAIRS, Arm 
assembly - lower.
2.Remove bush using LRT-64-028/1 with LRT-
64-028/2 and LRT-64-028/3 in direction shown.
3.Repeat procedure for other side.
Refit
1.Ensure bush and bush location in lower arm is 
clean.
2.Fit bush using LRT-64-028/4 with LRT-64-028/
2 and LRT-64-028/3 in direction shown.
3.Repeat procedure for...

REAR SUSPENSION
64-18 REPAIRS
Arm assembly - lower 
$% 64.35.54 
Do not depressurise air suspension system before 
raising vehicle
Remove
1.Raise rear of vehicle and support under body.
WARNING: Do not work on or under a 
vehicle supported only by a jack. Always 
support the vehicle on safety stands.
2.Remove anti-roll bar link.
 
 +  REAR SUSPENSION, REPAIRS, Link 
- anti roll bar.
3.Remove nut and bolt securing sensor link to 
lower arm.
4.Position jack to support the lower arm.
5.Depressurise rear...

REAR SUSPENSION
REPAIRS 64-19
7.Align damper to lower arm, fit through bolt and 
tighten to 110 Nm (81 lbf.ft).
8.Tighten bolts securing lower arm to subframe to 
165 Nm (121 lbf.ft).
9.Pressurise suspension. 
 
 +  REAR SUSPENSION, 
ADJUSTMENTS, Suspension - depressurise 
and repressurise.
10.Align height sensor link to lower arm, fit nut and 
bolt and tighten to 19 Nm (14 lbf.ft).
11.Fit anti-roll bar link.
 
 +  REAR SUSPENSION, REPAIRS, Link 
- anti roll bar.
12.Remove stands and lower vehicle.
Arm...

REAR SUSPENSION
64-20 REPAIRS
7.Remove Allen screw securing hand brake 
cable bracket.
8.Position jack to support the lower arm.
9.Reference mark eccentric in relationship to 
upper arm.
10.Remove and discard nut and bolt securing hub 
to upper arm. Release hub from arm.
11.Remove clip from air spring upper mounting.12.Remove bolt securing damper to lower arm.
13.Release damper from lower arm.
14.Support weight of subframe assembly on a jack
15.Remove 2 bolts securing subframe to body.
16.Lower subframe...

REAR SUSPENSION
REPAIRS 64-21
18.Remove 2 bolts securing upper arm.
19.Remove upper arm.
Refit
1.Clean upper arm bush locations.
2.Fit upper arm, fit bolts but do not tighten at this 
stage.
CAUTION: Nuts and bolts must be tightened 
with vehicle at normal ride height.
3.Align damper to lower arm, fit through bolt and 
tighten to 110 Nm (81 lbf.ft).
4.Tighten bolts securing upper arm to subframe 
to 165 Nm (121 lbf.ft).
5.Fit washers to subframe bushes.
6.Raise subframe, fit bolts securing subframe to...