Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

STEERING
57-24 REPAIRS
Oil cooler - power steering - Td6 
$% 57.15.11 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove front grille.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Front grille.
3.Remove viscous coupling.
 
 +  COOLING SYSTEM - Td6, REPAIR, 
Coupling unit - viscous fan.
4.Remove 2 bolts securing fuel cooler intake duct 
to bonnet...

STEERING
REPAIRS 57-25
11.Release and disconnect PAS hoses from fluid 
cooler.
CAUTION: Before disconnecting or 
removing components, ensure the 
immediate area around joint faces and 
connections are clean. Plug open 
connections to prevent contamination.
12.Ease radiator assembly rearward, release PAS 
cooler from retaining clips and remove.
Refit
1.Clean PAS cooler pipe connections.
2.Fit and secure PAS cooler.
3.Fit and secure condenser fan cowl assembly.
4.Position radiator to mounting, fit and...

STEERING
57-26 REPAIRS
7.Release 2 clips securing fan cowl to cooling 
pack and position the fan cowl aside.
8.Carefully release and remove PAS cooler from 
the cooling pack.
Refit
1.Clean PAS cooler pipe connections.
2.Fit and secure PAS cooler.
3.Fit and secure fan cowl to the cooling pack.
4.Fit cooling pack to the mounting bracket.
5.Fit and secure PAS hoses to cooler.
6.Fit radiator assembly.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Radiator.
7.Fit front grille.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Front...

STEERING
REPAIRS 57-27
8.Position container, release and disconnect 
return hose from PAS cooler.
CAUTION: Before disconnecting or 
removing components, ensure the 
immediate area around joint faces and 
connections are clean. Plug open 
connections to prevent contamination.
9.Remove 4 bolts and remove PAS pump.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
10.Remove 5 Torx screws and remove brackets 
from PAS pump.Refit
1.Fit brackets to PAS pump and tighten Torx...

STEERING
57-28 REPAIRS
Pump - power steering - V8 
$% 57.20.14 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove undertray.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Undertray - front.
4.Loosen 2 ancillary drive belt tensioner bolts.
5.Rotate tensioner fully clockwise to release 
tension on drive belt.
6.Release...

STEERING
REPAIRS 57-29
4.Position PAS pump to mounting, fit Allen bolts 
and securing nut. Tighten Allen bolts to 10 Nm 
(7 lbf.ft) and securing nut to 25 Nm (18 lbf.ft).
5.Remove plug connections, connect PAS feed 
hose to PAS pump and secure with clip.
6.Clean PAS pump and pipe union.
7.Fit new O ring to high pressure pipe union, 
align to PAS pump and tighten PAS pump high 
pressure pipe union to 25 Nm (18 lbf.ft).
8.Fit ancillary drive belt to all pulleys except 
tensioner pulley.
9.Fit ancillary...

STEERING
57-30 REPAIRS
8. Models with manual steering column 
control only:  Disconnect multiplug from 
steering column control module.
9.Disconnect multiplugs from steering column 
adjustment and lock motors.
10.Remove cable tie and disconnect multiplug 
from steering angle sensor.
Protect fascia shroud adjacent to steering 
column aperture.11.Release closing panel light harness, from 
securing clip in column frame.
12.Remove 4 bolts from steering column, carefully 
release column shaft from steering...

STEERING
REPAIRS 57-31
13.Ensure nylon sealing ring is fitted to steering 
shaft. If sealing ring is missing, remove it from 
column gaiter and fit to redundant steering 
shaft.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
14.Remove nut and bolt from lower steering shaft 
to column, remove shaft.
15. Models with manual steering column 
control only:  Remove 2 screws from steering 
control module and remove module
Refit
1. Models with manual steering column 
control...

STEERING
57-32 REPAIRS
Sensor- steering angle/column 
$% 57.40.02
Remove
1.Remove steering column assembly.
 
 +  STEERING, REPAIRS, Column 
assembly - inner & outer.
2.Release steering angle sensor from retaining 
clip and remove from shaft.
Refit
1.Position steering angle sensor to shaft and 
secure to retaining clip.
NOTE: Make sure the steering angle sensor is 
correctly aligned to the steering shaft. 
2.Fit steering column assembly.
 
 +  STEERING, REPAIRS, Column 
assembly - inner & outer....

STEERING
REPAIRS 57-33
Switch - column adjustment - control 
$% 57.41.05
Remove
1.Remove rotary coupler.
 
 +  RESTRAINT SYSTEMS, REPAIRS, 
Rotary coupler.
2.Release clip securing switch to rotary coupler 
and remove switch assembly.
Refit
1.Position switch assembly to rotary coupler, fit 
and secure clip.
2.Fit rotary coupler.
 
 +  RESTRAINT SYSTEMS, REPAIRS, 
Rotary coupler.
Ball joint - track rod 
$% 57.55.07
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a 
vehicle supported only...