Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

STEERING
57-34 REPAIRS
2.Fit track rod end to track rod the number of 
turns noted on removal.
3.Clean track rod end taper and taper seat.
4.Connect track rod end to steering arm, fit new 
nut and tighten to 80 Nm (59 lbf.ft).
5.Fit road wheel and tighten nuts to 140 Nm (103 
lbf.ft).
6.Remove stands and lower vehicle.
7.Check and adjust front wheel alignment.
 
 +  STEERING, ADJUSTMENTS, Front 
wheel alignment - check & adjust.
Steering wheel 
$% 57.61.01
Remove
1.Remove airbag module from steering...

STEERING
REPAIRS 57-35
4. RHD vehicles:With the wheels in the straight 
ahead position, the bottom timing mark on the 
steering column must be aligned with the 
steering wheel mark, see illustration above.
NOTE: The steering column timing marks are 
105
° apart.
LHD vehicles
5. LHD vehicles:With the wheels in the straight 
ahead position, the bottom timing mark on the 
steering column must be aligned with the 
steering wheel mark, see illustration above.
NOTE: The steering column timing marks are 
105
°...

STEERING
57-36 REPAIRS
Switch unit - steering wheel 
$% 57.61.02 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
WARNING: Always disconnect both battery leads 
before beginning work on the SRS system. 
Disconnect the negative lead first. Never reverse 
connect the battery.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS)...

FRONT SUSPENSION
ADJUSTMENTS 60-1
FRONT SUSPENSION ADJUST ME NTS
Air suspension system - depressurise 
and repressurise
$% 60.50.38
Depressurise
1.Depressurise suspension using TestBook/T4.
WARNING: The air suspension system is 
pressurised up to: 
lUp to VIN 106309 - 13.7 Bar (199 lbf/in2)
lFrom VIN 106310 - 11.8 Bar (171 lbf/in2) 
WARNING: Ensure dirt or grease does not 
enter the system. Wear hand, ear and eye 
safety protection when working on the 
system.
Repressurise
1.Repressurise suspension using...

FRONT SUSPENSION
60-2 ADJUSTMENTS 

FRONT SUSPENSION
REPAIRS 60-3
REPAIRS
Anti-roll bar 
$% 60.10.01
Remove
1.Remove undertray.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Undertray - front.
2.Raise front of vehicle and support under body.
WARNING: Do not work on or under a 
vehicle supported only by a jack. Always 
support the vehicle on safety stands.
3.Remove front road wheels.
4.Remove nuts securing anti-roll bar links and 
release links from anti-roll bar.
CAUTION: Use an open ended spanner on 
flats provided to prevent ball joint rotating.
5....

FRONT SUSPENSION
60-4 REPAIRS
11.Manoeuvre anti-roll bar over subframe and 
remove from vehicle.
CAUTION: The anti roll bar clamps are 
supplied with the anti roll bar and must not 
be removed.
Refit
1.Position anti-roll bar to subframe and 
manoeuvre into position.
2.Locate clamps and lightly tighten nuts.
3.Raise subframe, fit new bolts securing 
subframe to body and tighten to 165 Nm (122 
lbf.ft). Tighten 2 rear bolts a further 90°. 
4.Tighten bolts securing subframe to front 
crossmember to 132.5 Nm...

FRONT SUSPENSION
REPAIRS 60-5
6.Remove link and collect washer fitted to top ball 
joint.
CAUTION: Note position of washer for refit.
Refit
1.Fit washer to ball joint, fit anti-roll bar link, fit 
nuts and tighten to 100 Nm (74 lbf.ft). 
CAUTION: The washer is hardened and 
must be fitted in the correct position.
2.Fit road wheel and tighten nuts to 140 Nm (103 
lbf.ft).
3.Remove stands and lower vehicle.
Ball joint - tie rod
$% 60.15.04
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a...

FRONT SUSPENSION
60-6 REPAIRS
6.Using LRT-54-027 release lower arm ball joint 
and disconnect lower arm from hub.
CAUTION: Ensure ball joint seal is not 
damaged. A damaged seal will lead to 
premature failure of the joint.
7.Loosen bolt securing tie rod to subframe one 
quarter of a turn.
8.Remove nut securing tie rod to ball joint.
9.Using LRT-54-027 release tie rod from ball joint10.Remove 2 bolts securing ball joint. Discard 
bolts.
11.Remove ball joint.
Refit
1.Clean ball joint and mating face....

FRONT SUSPENSION
REPAIRS 60-7
Air spring assembly  
$% 60.21.01 
Do not depressurise air suspension system before 
raising vehicle. 
It is not necessary to depressurise the whole system, 
only the spring being replaced.
When removing Voss connectors from any air 
suspension component the connector must be left 
attached to the air pipe being removed. Do not 
remove the connector from the air pipe. Removing 
the connector from the air pipe could cause the 
connector to scratch the pipe and increase the...