Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

STEERING
57-14 REPAIRS
Power steering rack - right hand drive - 
V8 
$% 57.10.01 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove air intake plenum.
 
 +  HEATING AND VENTILATION, 
REPAIRS, Filter - fresh air intake.
3.Raise front of vehicle and support under body.
4.Remove undertray.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Undertray -...

STEERING
REPAIRS 57-15
14.Remove screw securing fan cowl to radiator.
15.Remove scrivets securing fan cowl.
16.Release fan cowl from radiator.17.Fit LRT-12-216 to engine lifting eyes.
18.Connect chain to lifting bracket and take weight 
of engine.
19.Remove nut securing LH engine mounting to 
engine mounting bracket.
20.Remove nut securing RH engine mounting to 
engine mounting bracket. 

STEERING
57-16 REPAIRS
21.Raise engine sufficiently only to clear engine 
mountings.
CAUTION: To prevent damage to the 
radiator, guide the fan cowl clear of the 
radiator as it is raised with the engine.
22.Disconnect multiplug from PAS rack pinion 
sensor.
23.Note fitted position of lower steering column. 
Remove Torx bolt from clamp and disconnect 
lower steering column from PAS rack. Discard 
Torx bolt.
CAUTION: Do not turn the steering wheel 
with the lower steering column 
disconnected as damage to...

STEERING
REPAIRS 57-17
27.Remove 2 bolts securing sub-frame to cross 
member and 6 bolts securing sub-frame to 
body.  Discard bolts.
28.With assistance, lower and remove sub-frame 
assembly.
29.Note orientation of PAS fluid feed and return 
hoses, remove banjo bolts and remove hoses. 
Discard sealing washers.
CAUTION: Always fit plugs to open 
connections to prevent contamination.
30.Remove 2 bolts and nuts securing PAS rack, 
remove rack, discard nuts and bolts.
NOTE: Do not carry out further...

STEERING
57-18 REPAIRS
10.Fit anti-roll bar heatshield and tighten fixings.
11.Lower engine onto mountings.
NOTE: Guide the fan cowl into position as the 
engine is lowered.
12.Fit fan cowl to radiator and fit securing scrivets.
13.Fit screw securing fan cowl to radiator.
14.Fit 2 nuts securing engine mountings to engine 
mounting brackets and tighten to 100 Nm (74 
lbf.ft).
15.Remove engine lifting chains.
16.Remove engine lifting bracket.
17.Connect lower steering column to PAS rack 
making sure that...

STEERING
REPAIRS 57-19
Power steering rack - right hand drive - 
Td6 
$% 57.10.01 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove 4 bolts securing the air flow panel and 
remove panel.
4.Remove viscous coupling.
 
 +  COOLING SYSTEM - Td6, REPAIR, 
Coupling unit - viscous fan.
5.Remove air intake plenum.
 
 +...

STEERING
57-20 REPAIRS
11.Remove Torx screw from steering column 
lower clamp.
12.Rotate steering wheel to straight ahead 
position, align pinion timing marks and remove 
ignition key.
CAUTION: Do not turn the steering wheel 
with the intermediate shaft or universal joint 
disconnected as damage to the rotary 
coupler and the steering wheel switches 
may occur.
13.Disconnect column from pinion.
14.Release vacuum hose from 3 clips on engine 
LH mounting bracket.
15.Disconnect mounting vacuum supply hose...

STEERING
REPAIRS 57-21
17.Disconnect height sensor multiplugs.
18.Disconnect multiplug from PAS rack pinion 
sensor.
19.Position container to collect PAS fluid spillage.
20.Loosen union nut, disconnect PAS outlet hose 
from pump and discard O ring.
CAUTION: Before disconnecting or 
removing components, ensure the 
immediate area around joint faces and 
connections are clean. Plug open 
connections to prevent contamination.21.Remove nut securing PAS hose to mounting.
22.Release and disconnect PAS return...

STEERING
57-22 REPAIRS
25.Remove 2 bolts securing sub-frame to cross 
member and 6 bolts securing sub-frame to 
body.  Discard bolts.
26.With assistance, lower and remove sub-frame 
assembly.27.Note orientation, remove banjo bolts securing 
fluid feed and return hoses to PAS rack and 
discard sealing washers.
CAUTION: Before disconnecting or 
removing components, ensure the 
immediate area around joint faces and 
connections are clean. Plug open 
connections to prevent contamination.
28.Release 5 clips...

STEERING
REPAIRS 57-23
29.Remove 2 bolts and nuts securing PAS rack, 
remove rack, discard nuts and bolts.
30.Loosen track rod end locknuts.
31.Remove track rod end ball joints from PAS 
rack. Note the number of threads for refit.
32.Remove and discard locking rings.
33.Remove locking nuts.
Refit
1.Fit locking nuts to track rods.
2.Fit locking rings to track rods, ensure taper 
faces track rod end.
3.Fit track rod ends to track rods the number of 
turns noted on removal.
4.Fit PAS rack, tighten new bolts...