Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

DRIVESHAFTS
47-14 REPAIRS
Bearing driveshaft support  
$% 47.10.41
Remove
1.Remove RH drive shaft seal.
 
 +  DRIVESHAFTS, REPAIRS, Seal - 
drive shaft - front - RH.
2.Remove 4 bolts, remove support housing and 
discard O ring.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
3.Remove oil seal from housing.
4.Remove bearing from housing.
Refit
1.Clean bearing and mating face.
2.Lubricate bearing with clean differential oil. 
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND...

DRIVESHAFTS
REPAIRS 47-15
O Ring - driveshaft housing  
$% 47.10.43
Remove
1.Remove RH drive shaft seal.
 
 +  DRIVESHAFTS, REPAIRS, Seal - 
drive shaft - front - RH.
2.Remove 4 bolts, remove support housing and 
discard O ring.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
Refit
1.Clean O ring groove, housing and mating face.
2.Lubricate new O ring and fit to housing.
3.Carefully fit housing and tighten bolts to 22 Nm 
(16 lbf.ft).
4.Fit RH drive shaft seal.
 
 +...

DRIVESHAFTS
47-16 REPAIRS
7.Fit centre screw LRT-60-030/3 to LRT-60-030/
1 and fit to hub with spacer LRT-60-030/2. 
Secure with nuts LRT-60-030/5.
8.Tighten centre screw to press drive shaft from 
flange.
9.Remove tools.
10.Position jack to support the lower arm.
11.Remove nut and bolt securing lower arm to 
hub.
12.Lower support jack.
13.Release drive shaft from differential.
14.Release drive shaft from hub, and with 
assistance, raise upper arm and remove drive 
shaft.
Refit
1.Clean end of drive shaft...

DRIVESHAFTS
REPAIRS 47-17
Gaiter - bell & joint - outer - rear
$% 47.11.03
Remove
1.Remove drive shaft.
 
 +  DRIVESHAFTS, REPAIRS, Drive 
shaft - rear.
2.Place drive shaft in vice.
3.Release and discard both drive shaft gaiter 
clips.
4.Slide gaiter along shaft to gain access to outer 
joint.
5.Using a drift against the inner part of the joint, 
remove joint from shaft.
6.Remove circlip from shaft and discard.
7.Remove gaiter from shaft.Refit
1.Clean drive shaft.
2.Fit gaiter.
3.Fit new circlip to drive...

DRIVESHAFTS
47-18 REPAIRS
Gaiter - inner joint 
$% 47.11.16
Remove
1.Remove rear drive shaft.
 
 +  DRIVESHAFTS, REPAIRS, Drive 
shaft - rear.
2.Place drive shaft in vice.
3.Remove and discard dust cover from drive 
shaft.4.Release and discard both drive shaft gaiter 
clips.
5.Slide gaiter along drive shaft to gain access to 
inner joint.
6.Remove excess grease from drive shaft.
7.Remove and discard circlip from drive shaft.
8.Reference mark drive shaft and joint for 
assembly purposes.
M47 0445 

DRIVESHAFTS
REPAIRS 47-19
9.Supporting drive shaft joint, use LRT-12-076 to 
remove joint from drive shaft.
10.Remove and discard joint retaining ring from 
drive shaft.
11.Remove gaiter from drive shaft.Refit
1.Clean drive shaft and joint.
2.Fit gaiter to drive shaft.
3.Fit new joint retaining ring to drive shaft.
4.Ensure reference marks are aligned and fit joint 
to drive shaft.
5.Fit new circlip to drive shaft.
6.Apply grease from the sachet to the joint.
7.Position gaiter to joint and secure to...

DRIVESHAFTS
47-20 REPAIRS
Propeller shaft - front  
$% 47.15.02
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Raise vehicle on lift.
4.Raise vehicle to allow propeller shaft to rotate.
5.Remove 6 nuts and bolts securing drive flange 
and propeller shaft to coupling. Discard locking 
nuts.
6.Pull propeller shaft rearwards and remove 
coupling and centering flange.
7.Reference mark propeller shaft and differential 
to aid reassembly.
8.Remove propeller shaft.
9.Remove and discard O...

DRIVESHAFTS
REPAIRS 47-21
Propeller shaft - rear 
$% 47.15.03
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove exhaust system.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- V8, REPAIRS, Exhaust system & 
mountings.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- Td6, REPAIR, Exhaust system and 
mountings.
4. Petrol models only: Remove 5 nuts securing 
LH heat shield. Remove heat shield.
5.Remove 8 nuts securing centre heat shield and 
remove shield.6.Remove 8 hexagonal headed screws securing...

DRIVESHAFTS
47-22 REPAIRS
11.Remove 6 Torx bolts securing propeller shaft to 
transfer gearbox flange.
12.Release joint from transfer gearbox flange and 
support the shaft.
13.Remove 2 nuts securing support bearing and 
remove propeller shaft.
Refit
1.Fit propeller shaft, fit nuts securing support 
bearing but do not tighten at this stage.
2.Clean propeller shaft joints and mating faces.
3.Fit propeller shaft joints to flanges and align 
marks. Tighten Torx bolts securing propeller 
shaft to transfer...

DRIVESHAFTS
REPAIRS 47-23
Support bearing - rear  
$% 47.20.06
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove rear propeller shaft.
 
 +  DRIVESHAFTS, REPAIRS, Propeller 
shaft - rear.
4.Reference mark rear propeller shaft for 
reassembly.
5.Remove bolt securing front part to rear part of 
propeller shaft.
6.Remove rear part of propeller shaft.
7.Remove shim from shaft.
8.Use press bars under support bearing as 
illustrated.
9.Fit LRT-37-011/2 to end of shaft and press...