Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

DRIVESHAFTS
47-4 REPAIRS
26.Tighten new bolt securing tie rod to subframe to 
165 Nm (121 lbf.ft), plus a further 90°.
CAUTION: Nuts and bolts must be tightened 
with vehicle at normal ride height.
27.Top-up differential with oil.
 
 +  FRONT DIFFERENTIAL, 
ADJUSTMENTS, Front differential - drain 
and refill.
28.Check front wheel alignment. 
 
 +  STEERING, ADJUSTMENTS, Front 
wheel alignment - check & adjust.
Drive shaft - front - RH  
$% 47.10.02
Remove
1.Raise front of vehicle.
WARNING: Do not work on...

DRIVESHAFTS
REPAIRS 47-5
4.Release drive shaft hub nut stake.
5.With an assistant applying brakes, remove and 
discard drive shaft hub nut.
6.Remove brake disc.
 
 +  BRAKES, REPAIRS, Brake disc - 
front.
7.Release ABS sensor lead from clip.
8.Release sensor lead from damper, remove 
Allen screw and release ABS sensor from hub.9.Remove and discard nut securing track rod ball 
joint to steering arm.
10.Fit an M14 nut to ball pin, flush with end of pin.
11.Using LRT-57-036 separate ball pin from 
steering...

DRIVESHAFTS
47-6 REPAIRS
15.Using LRT-54-027 release lower arm ball joint 
and disconnect lower arm from hub.
CAUTION: Ensure ball joint seal is not 
damaged. A damaged seal will lead to 
premature failure of the joint.
16.Loosen bolt securing tie rod to subframe one 
quarter of a turn.
17.Remove nut securing tie rod to ball joint.18.Using LRT-54-027 release tie rod from ball joint
CAUTION: Ensure ball joint seal is not 
damaged. A damaged seal will lead to 
premature failure of the joint.
19.Fit centre...

DRIVESHAFTS
REPAIRS 47-7
23.Fit LRT-54-026 to drive shaft inboard joint.
24.Using  levers, release drive shaft from 
differential.
25.Release drive shaft from hub.
26.With assistance, raise anti-roll bar to clear 
inboard joint.
27.Remove drive shaft assembly, keep drive shaft 
horizontal to avoid damaging differential oil 
seal.
28.Remove and discard drive shaft circlip.
Refit
1.Clean end of drive shaft and location in 
differential.
2.Fit new circlip to drive shaft.
3.Clean oil seal register....

DRIVESHAFTS
47-8 REPAIRS
28.Tighten bolt securing lower arm to subframe to 
165 Nm (121 lbf.ft), plus a further 90°.
CAUTION: Nuts and bolts must be tightened 
with vehicle at normal ride height.
29.Tighten bolt securing tie rod to subframe to 165 
Nm (121 lbf.ft), plus a further 90°.
30.Top-up differential with oil.
 
 +  FRONT DIFFERENTIAL, 
ADJUSTMENTS, Front differential - drain 
and refill.
31.Check front wheel alignment. 
 
 +  STEERING, ADJUSTMENTS, Front 
wheel alignment - check & adjust.
Gaiter...

DRIVESHAFTS
REPAIRS 47-9
Refit
1.Clean drive shaft.
2.Fit new gaiter to shaft.
3.Fit new circlip to drive shaft.
4.Position outer joint to shaft, use a screwdriver 
to press circlip into its groove and push joint 
fully onto shaft.
5.Apply grease from the sachet to the joint.
6.Position gaiter to joint and secure to joint and 
shaft with new clips.
7.Fit drive shaft.
 
 +  DRIVESHAFTS, REPAIRS, Drive 
shaft - front - LH.
 
 +  DRIVESHAFTS, REPAIRS, Drive 
shaft - front - RH.
Gaiter - inner joint
$%...

DRIVESHAFTS
47-10 REPAIRS
3.Slide gaiter along drive shaft to gain access to 
inner joint.
4.Remove excess grease from joint and inner 
member.
5.Reference mark drive shaft and joint for 
assembly purposes.
6.Remove joint and inner member from drive 
shaft.
7.Remove gaiter from shaft and discard.
Refit
1.Clean drive shaft, joint and inner member.
2.Fit new gaiter to drive shaft.
3.Ensuring reference marks are aligned, fit joint 
and inner member to drive shaft.
4.Apply grease from the sachet to the...

DRIVESHAFTS
REPAIRS 47-11
6.Remove nuts securing anti-roll bar links and 
release links from anti-roll bar.
7.Remove nut securing height sensor link to 
lower arm and release link.
Caution: use an open ended spanner on 
flats provided to prevent ball joint rotating.
8.Loosen bolt securing lower arm to subframe 
one quarter of a turn.9.Remove nut securing lower arm ball joint to 
hub.
10.Using LRT-54-027 release lower arm ball joint 
and disconnect lower arm from hub.
Caution: ensure ball joint seal is...

DRIVESHAFTS
47-12 REPAIRS
13.Using LRT-54-027 release tie rod from ball joint
Caution: ensure ball joint seal is not 
damaged. A damaged seal will lead to 
premature failure of the joint.
14.Remove and discard nut securing track rod ball 
joint to steering arm.
15.Fit an m14 nut to ball pin, flush with end of pin.
16.Using LRT-57-036 separate ball pin from 
steering arm. Remove m14 nut and release ball 
pin from steering arm.
Caution: ensure ball joint seal is not 
damaged. A damaged seal will lead to...

DRIVESHAFTS
REPAIRS 47-13
2.Use LRT-54-028 to fit new oil seal.
3.Clean end of drive shaft.
4.Lubricate lip of oil seal with differential oil.
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, 
Lubrication.
5.Fit new circlip to drive shaft.
6.Lightly lubricate splines and oil seal running 
surface.
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, 
Lubrication.
7.With assistance, position hub and drive shaft 
assembly. Carefully fit drive shaft through seal, 
remove seal protector and push drive...