Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE - V8
12-2-58 REPAIRS
Gasket - oil sump 
$% 12.60.38 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove dipstick tube.
 
 +  Engine - V8, REPAIRS, Tube - 
dipstick.
4.Remove PAS pump.
 
 +  STEERING, REPAIRS, Pump - power 
steering - V8.
5.Remove differential.
 
 +  FRONT DIFFERENTIAL, REPAIRS,...

ENGINE - V8
REPAIRS 12-2-59
10.Remove 31 bolts securing oil sump to engine 
cylinder block, note position of bolts as lengths 
vary.
lA=M8 x 60 mm
lB=M6 x 80 mm
lC=M6 x 40 mm
lAll remaining bolts are M6 x 20 mm
11.Remove oil sump and discard gasket.
Refit
1.Clean oil sump and gasket mating faces.
2.Fit new gasket to sump, position sump to 
cylinder block, fit bolts but do not tighten at this 
stage.
3.Tighten 31 bolts securing upper oil sump to 
cylinder block, M6 x 8.8 mm to 10 Nm (7 lbf.ft), 
M6 x 10.9...

ENGINE - V8
12-2-60 REPAIRS
Baffle Plate 
$% 12.60.46 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove engine oil sump.
 
 +  Engine - V8, REPAIRS, Gasket - oil 
sump.
4.Remove 6 bolts securing baffle plate and 
remove plate.
Refit
1.Fit baffle plate and tighten bolts to 10 Nm (7 
lbf.ft).
2.Fit engine oil...

ENGINE - V8
REPAIRS 12-2-61
Refit
1.Clean oil pressure switch and oil filter housing 
mating faces.
2.Fit new sealing washer to oil pressure switch.
3.Fit oil pressure switch and tighten to 27 Nm (20 
lbf.ft).
4.Connect multiplug to oil pressure switch.
5.Remove absorbent cloth.
6.Connect battery earth lead.
7.Connect exhaust extractor to tail pipes.
8.Start engine and run at idle speed until oil 
pressure warning light extinguishes.
9.Check for leaks from oil pressure switch.
10.Stop engine, wait a few...

ENGINE - V8
12-2-62 REPAIRS
Cover - timing gear - upper - RH 
$% 12.65.39 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Remove fan cowl.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Coupling unit - viscous fan.
5.Release...

ENGINE - V8
REPAIRS 12-2-63
9.Disconnect multiplug from VCC solenoid.
10.Remove RH camshaft cover.
 
 +  Engine - V8, REPAIRS, Gasket - 
camshaft cover - RH.
11.Release clip and disconnect coolant hose from 
coolant pump.
12.Release clip, disconnect radiator bottom hose 
from thermostat housing and remove bolt 
securing P clip.13.Remove bolt securing SAI pipe to LH cylinder 
head.
14.Remove bolt securing SAI pipe to RH cylinder 
head.
15.Remove Allen bolt securing secondary air 
injection (SAI) pipe clip...

ENGINE - V8
12-2-64 REPAIRS
17.Remove 2 bolts securing VCC solenoid seal 
and remove seal.
18.Remove chain tensioner from timing gear cover 
and discard sealing washer. Separate oil 
tensioner body and allow oil to drain.
19.Remove 6 bolts securing timing gear cover to 
cylinder head and remove timing gear cover.
20.Discard timing gear cover gasket.21.Discard timing chain tensioner O ring.NOTE: Do not carry out further dismantling if 
component is removed for access only.
22.Remove bolt securing CMP...

ENGINE - V8
REPAIRS 12-2-65
8.Fit LRT-12-225/1 to RH camshaft cover.
9.Fit camshaft cover and tool, fit 4 bolts and 
tighten to 10 Nm (7 lbf.ft).
10.Tighten bolts securing timing gear cover to 15 
Nm (11 lbf.ft).
11.Remove 4 bolts securing camshaft cover, 
remove camshaft cover and LRT-12-225/1.
12.Fit new sealing washer, fit timing chain 
tensioner and tighten plug securing chain 
tensioner to 40 Nm (30 lbf.ft).
13.Clean VCC solenoid, VCC solenoid seal and 
mating faces.
14.Lubricate inner mating face...

ENGINE - V8
12-2-66 REPAIRS
Cover - timing gear - upper - LH 
$% 12.65.41 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Remove fan cowl.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Coupling unit - viscous fan.
5.Remove...

ENGINE - V8
REPAIRS 12-2-67
15.Remove bolt securing SAI pipe to LH cylinder 
head.
16.Remove bolt securing SAI pipe to RH cylinder 
head.
17.Remove Allen bolt securing secondary air 
injection (SAI) pipe clip to coolant pump.
18.Release SAI pipe from cylinder heads and 
position aside. Discard O rings.19.Remove 6 bolts securing timing gear cover to 
cylinder head and remove timing gear cover.
20.Discard timing gear cover gasket.
NOTE: Do not carry out further dismantling if 
component is removed for...