Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE - V8
12-2-18 REPAIRS
Control solenoid - variable camshaft 
control (VCC) - LH
$% 12.30.60 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Release clip and disconnect coolant hose from 
coolant pump.
5.Disconnect...

ENGINE - V8
REPAIRS 12-2-19
Control solenoid - variable camshaft 
control (VCC) - RH
$% 12.30.61 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to 
throttle body.
3.Disconnect multiplug from VCC solenoid.
4.Remove 2 bolts securing VCC solenoid seal...

ENGINE - V8
12-2-20 REPAIRS
Variable camshaft unit - variable 
camshaft control (VCC) - LH
$% 12.30.62 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Remove fan cowl.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Coupling unit...

ENGINE - V8
REPAIRS 12-2-21
12.Position LRT-12-227 through timing tool 
access hole and secure flywheel in TDC 
position.
13.Remove LH upper timing gear cover.
 
 +  Engine - V8, REPAIRS, Cover - 
timing gear - upper - LH.
14.Remove RH upper timing gear cover.
 
 +  Engine - V8, REPAIRS, Cover - 
timing gear - upper - RH.
15.Remove nut securing LH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread is left handed.
16.Remove nut securing RH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread...

ENGINE - V8
12-2-22 REPAIRS
19.Loosen bolt securing LRT-12-223/2 to LRT-12-
223/1.
20.Fit LRT-12-223/2 and LRT-12-223/1 to rear of 
RH camshafts and tighten bolt securing tools.
21.Fit LRT-12-223/5, LRT-12-223/6 to RH cylinder 
head and tighten LRT-12-223/6 into spark plug 
thread.
22.Loosen bolt securing LRT-12-223/4 to LRT-12-
223/3.23.Fit LRT-12-223/4 and LRT-12-223/3 to rear of 
LH camshafts and tighten bolt securing tools.
24.Fit LRT-12-223/5, LRT-12-223/6 to LH cylinder 
head and tighten...

ENGINE - V8
REPAIRS 12-2-23
26.Remove LH exhaust camshaft sprocket, LH 
exhaust camshaft chain and LH VCC unit.
NOTE: Secure chain to cylinder head to 
prevent chain falling into lower timing gear 
cover.
Refit
1.Position LH exhaust camshaft chain to LH VCC 
unit and position LH exhaust camshaft sprocket 
to LH exhaust camshaft chain.
NOTE: The VCC unit, exhaust camshaft chain 
and exhaust camshaft sprocket do not have 
timing marks on them. These parts may be 
freely fitted to the timing gear chain and...

ENGINE - V8
12-2-24 REPAIRS
9.Rotate RH VCC unit using LRT-12-224 to 40 
Nm (30 lbf.ft) and using the multimeter, check 
continuity is present.
NOTE: Rotating the VCC unit using LRT-12-
224 will remove the oil cushion and make sure 
the VCC unit is at the full LH stop position. 
Continuity should be present when the VCC 
unit reaches this position.
10.Tighten Torx bolts securing RH VCC unit and 
exhaust camshaft sprocket to 15 Nm (11 lbf.ft) 
and loosen one quarter of a turn.
NOTE: Thread is left...

ENGINE - V8
REPAIRS 12-2-25
19.Position LRT-12-228/1 locating dowel to RH 
CMP sensor ring, fit 2 bolts securing tool to RH 
cylinder head and tighten.
NOTE: To ensure correct CMP sensor ring 
adjustment, make sure the tool  is aligned flush 
with the cylinder head and lower timing gear 
cover before tightening the tool securing bolts.
20.Tighten nut securing CMP sensor ring to 40 Nm 
(30 lbf.ft) and remove LRT-12-228/1 from RH 
cylinder head.
NOTE: Thread is left handed.
21.Fit LH CMP sensor ring, fit...

ENGINE - V8
12-2-26 REPAIRS
Variable camshaft unit - variable 
camshaft control (VCC) - RH 
$% 12.30.63 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Remove fan cowl.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Coupling...

ENGINE - V8
REPAIRS 12-2-27
12.Position LRT-12-227 through timing tool 
access hole and secure flywheel in TDC 
position.
13.Remove LH upper timing gear cover.
 
 +  Engine - V8, REPAIRS, Cover - 
timing gear - upper - LH.
14.Remove RH upper timing gear cover.
 
 +  Engine - V8, REPAIRS, Cover - 
timing gear - upper - RH.
15.Remove nut securing RH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread is left handed.
16.Remove nut securing LH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread...