Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE - V8
12-2-38 REPAIRS
52.Disconnect multiplug from A/C compressor.
53.Remove Allen bolt securing A/C pipe to A/C 
compressor and disconnect A/C pipe. Discard 
O ring.
CAUTION: Immediately cap all A/C pipes to 
prevent ingress of dirt and moisture into the 
system.54.Remove Allen bolt securing A/C pipe to 
condenser and disconnect A/C pipe. Discard 
O ring.
CAUTION: Immediately cap all A/C pipes to 
prevent ingress of dirt and moisture into the 
system.
55.Disconnect 2 hoses from the SAI control...

ENGINE - V8
REPAIRS 12-2-39
56.Disconnect multiplug from oil pressure switch.
57.Remove 2 nuts securing oil filter housing and 
release oil filter housing from mounting bracket.
58.Position oil filter housing and hoses aside and 
secure to engine with cable ties.
59.Position container to collect PAS fluid spillage.60.Release clip and disconnect fluid inlet hose 
from PAS pump. Undo union nut and 
disconnect PAS outlet hose from PAS pump. 
Discard O ring.
CAUTION: Always fit plugs to open 
connections to...

ENGINE - V8
12-2-40 REPAIRS
63.Remove 4 nuts securing front pipe flanges to 
exhaust manifolds and discard nuts.
64.Release exhaust front pipes from exhaust 
manifolds.
65.Remove front road wheels.
66.Remove RH front drive shaft.
 
 +  DRIVESHAFTS, REPAIRS, Drive 
shaft - front - RH.67.Remove differential breather hose. Remove 4 
differential securing bolts and release 
differential from engine sump.
NOTE: Securing bolt above pinion remains 
captive to differential.
68.Disconnect engine earth lead....

ENGINE - V8
REPAIRS 12-2-41
70.Remove bolt securing transmission cooler 
pipes and release cooler pipes from bracket.
71.Remove grommet from bottom of bell housing 
to gain access to torque converter.
72.Remove grommet from bell housing to gain 
access to torque converter securing bolts.
73.Rotate crankshaft for access and remove 4 
bolts securing torque converter to drive plate.
74.Position torque converter clear of drive plate.75.Remove 2 bolts securing starter motor and 
release starter motor.
NOTE:...

ENGINE - V8
12-2-42 REPAIRS
79.Remove nut securing RH engine mounting to 
engine mounting bracket.
80.Remove nut securing LH engine mounting to 
engine mounting bracket.
81.Connect chain to lifting bracket and take weight 
of engine.
82.Raise engine clear of mountings.
83.Remove 2 Torx bolts from top of bell housing.84.Release engine from dowels, carefully raise 
and guide engine clear of vehicle.
CAUTION: To prevent damage to the 
radiator, do not allow engine to contact the 
radiator.
85.Discard...

ENGINE - V8
REPAIRS 12-2-43
3.If necessary, continue to rotate crankshaft 
slightly to align TDC timing marks
4.Temporarily fit drive plate ensuring that hollow 
bush in drive plate securing bolt hole, is aligned 
with bolt hole A in crankshaft boss.
5.Fit and lightly tighten 8 drive plate securing 
bolts.
Do not fit a bolt in drive plate hole with hollow 
bush.
6.Fit timing pin LRT-12-227 ,ensuring that it is 
inserted in hole in drive plate.
If necessary, rotate crankshaft slightly to 
enable timing...

ENGINE - V8
12-2-44 REPAIRS
37.Fit new O ring to PAS hose union, connect 
hose to pump and tighten nut to 25 Nm (18 
lbf.ft).
38.Connect supply hose to PAS pump and secure 
using new clip.
39.Fit oil filter housing to bracket and tighten 
securing nuts.
40.Connect multiplug to oil pressure switch.
41.Connect SAI control valve hoses.
42.Fit new O rings to A/C pipes and lubricate with 
clean refrigerant oil.
43.Align A/C pipes to condenser and compressor. 
Fit Allen bolts securing A/C pipes to condenser...

ENGINE - V8
REPAIRS 12-2-45
Mounting - rear  
$% 12.45.08 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Raise vehicle on lift.
4.Remove exhaust system.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- V8, REPAIRS, Exhaust system & 
mountings.
5.Remove 8 nuts securing centre heat shield and 
remove shield.
6.Remove 5 nuts,...

ENGINE - V8
12-2-46 REPAIRS
12.Lubricate centre screw LRT-41-018/4 with 
Molybdenum Disulphide grease and assemble 
tool as shown to remove mounting from 
transfer gearbox.
CAUTION: Ensure tool alignment indicator 
is at the 6 oclock position. The tool 
alignment indicator is a machined flat, on 
LRT-41-018/1 and LRT-41-018/2.
Refit
1.Clean mounting and mating faces.
2.Lubricate new mounting and bore in transfer 
gearbox casing to aid assembly.
3.Position new mounting to rear face of transfer 
gearbox,...

ENGINE - V8
REPAIRS 12-2-47
9.Align cross member, fit bolts and tighten to 68 
Nm (50 lbf.ft).
10.Remove support from gearbox.
11.Tighten nut and bolt securing mounting to cross 
member to 100 Nm (74 lbf.ft).
12.Fit LH heat shield and secure with nuts.
13.Fit RH heat shield and secure with nuts.
14.Fit centre heat shield and secure with nuts.
15.Fit exhaust system.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- V8, REPAIRS, Exhaust system & 
mountings.
16.Connect battery earth lead.
Engine mounting - LH 
$%...