Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE - V8
12-2-88 OVERHAUL
4.Fit LRT-12-223/4 and LRT-12-223/3 to rear of 
LH camshafts and tighten bolt securing tools.
5.Fit LRT-12-223/5, LRT-12-223/6 to LH cylinder 
head and tighten LRT-12-223/6 into spark plug 
thread.
6.Rotate engine crankshaft pulley clockwise to 
align TDC timing mark.
NOTE: Raise timing chain and hold under 
tension while turning crankshaft pulley.
7.Position LRT-12-227 through timing tool 
access hole and secure flywheel in TDC 
position.
8.Fit LH VCC unit.
 
 +  Engine -...

ENGINE - V8
OVERHAUL 12-2-89
Cylinder head - overhaul  
$% 12.29.19.01
Disassembly
1.Remove 2 nuts securing exhaust camshaft 
drive chain tensioner, remove tensioner and  
discard O ring.
2.Remove 5 bolts securing VCC oil distribution 
housing. Remove sealing washer from long bolt 
and discard washer.
3.Remove VCC oil distribution housing, remove 
and discard gasket.
NOTE: If distribution unit is worn, move unit 
backwards and forwards to release from 
sealing rings.
4.Carefully release and remove 3 VCC...

ENGINE - V8
12-2-90 OVERHAUL
7.Using a spanner on the hexagon, rotate inlet 
camshaft until lobes of cylinder 8 face upwards.
8.Using a spanner on the hexagon, rotate 
exhaust camshaft until lobes of cylinder 6 face 
upwards.
9.Identify camshaft bearing caps for refitting. Inlet 
camshaft is marked E with caps marked from 
E1 to E5 from driven end of camshaft when 
viewed from inlet side of cylinder head. Exhaust 
camshaft is marked A with caps marked A1 to 
A5 from driven end of camshaft when viewed...

ENGINE - V8
OVERHAUL 12-2-91
19.Remove valve stem oil seal using LRT-12-071. 
Discard stem seal.
20.Repeat procedure for remaining valves, 
keeping components in their fitted order.
Inspect
1.Inspect camshafts and replace camshafts if 
scored, pitted or excessively worn.
 
 +  GENERAL DATA, Engine - V8.
2.Check camshaft, camshaft bearings in cylinder 
head and bearing caps for wear.
 
 +  GENERAL DATA, Engine - V8.
3.Using a straight edge and feeler gauges, check 
cylinder head for distortion along lines...

ENGINE - V8
12-2-92 OVERHAUL
11.Inspect the VCC oil distribution housing and 
sealing rings for signs of wear.
 
 +  GENERAL DATA, Engine - V8.
CAUTION: Replace distribution housing 
and sealing rings if pitting or scoring is 
evident in a longitudinal direction.
Reassembly
1.Clean combustion space valve guide and 
manifold ports, blow out with air line.
2.Clean valve, valve spring, spring seat, cap and 
collets.
3.Lubricate valve with clean engine oil and fit 
valve.
4.Fit LRT-12-104 over valve stem,...

ENGINE - V8
OVERHAUL 12-2-93
16.Using a new O ring, fit the VCC oil non return 
valve to the cylinder head.
CAUTION: VCC non-return valve to be fitted 
with M10 thread visible.
17.Clean VCC unit oil distribution rings and 
grooves in inlet camshaft.
18.Lubricate VCC oil distribution rings and 
carefully fit rings to grooves in inlet camshaft.
19.Clean VCC oil distribution housing and mating 
face on cylinder head. Ensure oil ways are 
clear.
20.Fit VCC oil distribution housing gasket to 
cylinder head....

ENGINE - V8
12-2-94 OVERHAUL
3. RH camshaft cover: Remove 2 nuts securing 
dipstick tube.
4. RH camshaft cover: Remove nut and clamp 
securing dipstick tube to oil sump.
5. RH camshaft cover: Remove dipstick tube 
and sealing washer, discard O ring.
6.Remove 8 nuts and 3 bolts securing camshaft 
cover to cylinder head. Remove camshaft 
cover, discard 2 gaskets and 11 sealing 
washers.Reassembly
1.Clean camshaft cover and mating face of 
cylinder head.
2.Apply sealant STC 50550 to areas illustrated.
3.Fit...

ENGINE - V8
OVERHAUL 12-2-95
Variable camshaft unit - variable 
camshaft control (VCC)
$% 12.30.62.01
Remove
1.Remove camshaft covers.
 
 +  Engine - V8, OVERHAUL, Gasket - 
covers - camshaft.
2.Remove 8 spark plugs.
3.Remove 2 bolts securing engine lifting eye to 
rear of RH cylinder head and remove lifting eye.
4.Remove 20 nuts securing 4 camshaft oil lines to 
LH and RH cylinder heads and remove 
camshaft oil lines.5.Rotate engine crankshaft pulley until cylinder 1 
camshaft lobes are at TDC firing...

ENGINE - V8
12-2-96 OVERHAUL
7.Position LRT-12-227 through timing tool 
access hole and secure flywheel in TDC 
position.
8.Remove timing gear upper covers.
 
 +  Engine - V8, OVERHAUL, Cover - 
timing gear - upper.
Disassembly
1.Remove nut securing LH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread is left handed.
2.Remove nut securing RH CMP sensor ring and 
remove CMP sensor ring.
NOTE: Thread is left handed.
3.Loosen 2 Torx bolts securing LH VCC unit and 
LH exhaust camshaft sprocket 1/2 a...

ENGINE - V8
OVERHAUL 12-2-97
4.Loosen 2 Torx bolts securing RH VCC unit and 
RH exhaust camshaft sprocket 1/2 a turn.
NOTE: Thread is left handed.
5.Loosen bolt securing LRT-12-223/2 to LRT-12-
223/1.
6.Fit LRT-12-223/2 and LRT-12-223/1 to rear of 
RH camshafts and tighten bolt securing tools.
7.Fit LRT-12-223/5, LRT-12-223/6 to RH cylinder 
head and tighten LRT-12-223/6 into spark plug 
thread.8.Loosen bolt securing LRT-12-223/4 to LRT-12-
223/3.
9.Fit LRT-12-223/4 and LRT-12-223/3 to rear of 
LH...