Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE MANAGEMENT SYSTEM - V8
18-2-10 REPAIRS
Sensor - camshaft position (CMP) - RH 
$% 18.30.26 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to 
throttle body.
3.Cut 3 cable ties to release CMP sensor 
harness.
4.Disconnect multiplug from CMP...

ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-11
Sensor - knock (KS) - LH 
$% 18.30.28 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove coolant pump to coolant manifold 
pipes.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Pipe(s) - coolant pump to coolant manifold.
3.Remove 2 bolts securing KS to cylinder block, 
remove sensors.
Refit
1.Clean KS...

ENGINE MANAGEMENT SYSTEM - V8
18-2-12 REPAIRS
Sensor - temperature - E box 
$% 18.30.77 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove 10 Allen screws securing E box cover 
and remove cover.
3.Disconnect multiplug from E box temperature 
sensor.
4.Remove E box temperature sensor.Refit
1.Fit E box temperature sensor to mounting....

ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-13
Housing - air cleaner
$% 19.10.01
Remove
1.Remove air cleaner element.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Element - air cleaner.
2.Remove bolt securing air cleaner lower 
housing.
3.Release clip securing air intake pipe to lower air 
cleaner housing.
4.Remove lower air cleaner housing.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
5.Remove mountings from lower air cleaner 
housing.
Refit
1.Fit mountings to...

ENGINE MANAGEMENT SYSTEM - V8
18-2-14 REPAIRS
Element - air cleaner 
$% 19.10.10
Remove
1.Release 2 clips securing MAF/IAT sensor to 
upper air cleaner housing. Disconnect SAI 
pump air intake hose from upper air cleaner 
housing.
2.Release 4 clips and remove upper air cleaner 
housing.
3.Discard O ring from upper air cleaner housing.4.Remove air cleaner element.
Refit
1.Clean air cleaner housing.
2.Fit air cleaner element.
3.Fit O ring seal into upper air cleaner housing.
4.Lubricate O ring.
5.Fit upper...

ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-15
Hose - air flow meter to throttle body 
$% 19.10.28
Remove
1.Remove engine acoustic cover.
 
 +  Engine - V8, REPAIRS, Acoustic 
cover - engine.
2.Disconnect vacuum pipes from air intake pipe.
3.Release 2 clips and disconnect air intake pipe 
from throttle body.
4.Remove air intake pipe.
5.Remove seal from air intake pipe, at MAF 
sensor connection end.
6.Remove clips from air intake pipe.Refit
1.Fit seal to MAF sensor.
2.Lubricate air intake pipe mating face...

ENGINE MANAGEMENT SYSTEM - V8
18-2-16 REPAIRS
Sensor - accelerator pedal position 
(APP)
$% 19.20.01 
The APP sensor is not serviced separately from the 
throttle pedal.
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove cap from screw and remove Allen 
screw securing throttle pedal.
3.Release pedal from bracket, disconnect 
multiplug from...

ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-17
Refit
1.Fit O ring seal into upper air cleaner housing.
2.Lubricate O ring with clean engine oil.
3.Fit MAF/IAT sensor into upper air cleaner 
housing and secure with clips.
4.Connect multiplug to MAF/IAT sensor.
5.Connect air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to 
throttle body.
6.Connect battery earth lead.
7.If a replacement sensor has been fitted, re-set 
adaptions using TestBook/T4.
Throttle body 
$%...

ENGINE MANAGEMENT SYSTEM - V8
18-2-18 REPAIRS
Refit
1.Clean mating faces of throttle housing and inlet 
manifold.
2.Fit 2 new throttle body seals.
3.Fit throttle housing to inlet manifold and tighten 
4 bolts to 10 Nm (7 lbf.ft).
4.Connect multiplug to throttle body.
5.Connect air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to 
throttle body.
6.If fitting a new throttle body, reset adaptions 
using TestBook/T4.
Fuel rail - remove for access & refit 
$% 19.60.04.99...

ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-19
6.Disconnect multiplugs from throttle body, 
thermostat heater, CMP sensor and ECT 
sensor.
7.Cut 2 cable ties and release engine harness.
8.Disconnect multiplugs from VCC solenoids.
9.Release VCC multiplug harness from clip.
10.Disconnect multiplug from charcoal canister 
purge solenoid valve.11.Disconnect alternator multiplug.
12.Release alternator harness from 4 clips.
13.Disconnect multiplugs from KS and CMP 
sensor.
14.Remove 2 nuts securing fuel...