Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

FUEL DELIVERY SYSTEM - V8
19-2-16 REPAIRS 

COOLING SYSTEM - V8
ADJUSTMENTS 26-2-1
COOLING SYSTEM -  V8 ADJUST ME NTS
Coolant - drain, flush & refill  
$% 26.10.01 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Drain
1.Position vehicle on lift.
2.Set heater controls to maximum.
3.Disconnect battery earth lead.
4.Remove coolant expansion tank cap.
WARNING: Since injury such as scalding 
could be caused by escaping steam or...

COOLING SYSTEM - V8
26-2-2 ADJUSTMENTS
10.Check for leaks and fill expansion tank to MAX 
mark.
11.Clean coolant from body and surrounding area.
12.Fit undertray.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Undertray - front. 

COOLING SYSTEM - V8
REPAIRS 26-2-3
REPAIRS
Coupling unit - viscous fan 
$% 26.25.19 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove undertray.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Undertray - front.
4.Release 3 coolant hoses from clips on fan cowl. 
Remove screw securing fan cowl to radiator.
5.Disconnect...

COOLING SYSTEM - V8
26-2-4 REPAIRS
8.Release cowl from mountings and remove cowl 
and fan assembly.
9.Place viscous coupling and fan to work bench.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
10.Remove 4 bolts and remove coupling from fan.
Refit
1.Clean coupling and fan mating faces.
2.Fit viscous coupling to fan and tighten 4 bolts to 
10 Nm (7 lbf.ft).
3.Carefully fit fan and cowl assembly, secure the 
cowl to mountings.
4.Fit fan assembly to coolant pump. Using...

COOLING SYSTEM - V8
REPAIRS 26-2-5
9.Remove bolt securing multiplug to bell housing.
10.Release transfer gearbox breather pipe from 
clip.
11.Remove 6 bolts securing coolant manifold to 
cylinder heads.
12.Secure coolant pipes and remove coolant 
manifold.
13.Remove harness retaining clips.
14.Discard O rings and gaskets.Refit
1.Clean coolant manifold and cylinder head 
mating faces.
2.Fit new O rings to coolant manifold.
3.Fit harness retaining clips.
4.Position new gaskets and coolant manifold to...

COOLING SYSTEM - V8
26-2-6 REPAIRS
Pipe(s) - coolant pump to coolant 
manifold 
$% 26.31.25
Remove
1.Drain coolant.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
2.Remove inlet manifold.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- V8, REPAIRS, Gasket(s) - inlet manifold.
3.Remove bolt securing engine harness to 
coolant manifold.
4.Release harness from 2 clips on coolant 
manifold.
5.Release transfer gearbox breather pipe from 
clip.
6.Remove 6 bolts securing coolant manifold to...

COOLING SYSTEM - V8
REPAIRS 26-2-7
Gasket - coolant gallery sealing plate  
$% 26.35.40 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove coolant pump to coolant manifold 
pipes.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Pipe(s) - coolant pump to coolant manifold.
4.Remove 20 bolts securing coolant gallery 
sealing...

COOLING SYSTEM - V8
26-2-8 REPAIRS
7.Remove radiator assembly retaining bolts from 
bonnet locking platform.
8.Ease radiator assembly rearward, release and 
remove radiator retaining clips.
9.Carefully remove radiator.
Refit
1.Position radiator to mounting, fit and secure 
retaining clips.
2.Position and secure radiator assembly to 
bonnet locking platform.
3.Position gearbox cooler to radiator and tighten 
securing screw.
4.Connect hoses to radiator and secure with 
clips.
5.Fit viscous coupling.
 
 +...

COOLING SYSTEM - V8
REPAIRS 26-2-9
7.Remove 4 bolts and remove thermostat 
housing from coolant pump. Discard seal.
Refit
1.Clean mating face of thermostat housing and 
coolant pump.
2.Fit new seal to thermostat housing.
3.Fit thermostat housing and tighten bolts to 10 
Nm (7 lbf.ft).
4.Connect radiator bottom hose to thermostat 
housing and secure with clip.
5.Connect multiplug to thermostat heater.
6.Connect air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to...