Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

COOLING SYSTEM - V8
26-2-10 REPAIRS
7.Remove Allen bolt securing secondary air 
injection (SAI) pipe clip to coolant pump.
8.Remove bolt securing SAI pipe to LH cylinder 
head.
9.Remove bolt securing SAI pipe to RH cylinder 
head.
10.Release SAI pipe from cylinder heads and 
position aside. Discard O rings.11.Using LRT-12-215 to hold coolant pump pulley, 
loosen 4 bolts securing coolant pump pulley.
12.Remove 4 bolts securing coolant pump pulley 
and remove pulley.
13.Disconnect ECT sensor multiplug.
M26...

COOLING SYSTEM - V8
REPAIRS 26-2-11
14.Remove 6 bolts securing coolant pump to 
cylinder block and remove coolant pump.
NOTE: Do not allow the coolant pipes to be 
released from the coolant manifold during the 
removal of the coolant pump. If the coolant 
pipes are released from the coolant manifold 
the O rings must be replaced.
15.Remove and discard 2 O rings from coolant 
pump.
16.Clean gasket mating faces.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
17.Remove...

COOLING SYSTEM - V8
26-2-12 REPAIRS 

MANIFOLD AND EXHAUST SYSTEM - V8
REPAIRS 30-2-1
MANIF OLD A ND EXH AUST SYSTEM - V8 REPAIRS
Exhaust system & mountings 
$% 30.10.08 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Release pre-catalyst harness leads from clips, 
remove multiplugs from retaining clips and 
disconnect.
4.Release post catalyst HO2S...

MANIFOLD AND EXHAUST SYSTEM - V8
30-2-2 REPAIRS
6.Remove and discard the 4 nuts securing 
intermediate silencer mountings to body.
7.Remove 8 nuts securing rear silencer rubber 
mountings to body and with assistance remove 
exhaust assembly from vehicle.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
8.Remove 2 nuts and collect mass damper.9.Remove 6 mounting rubbers from main 
assembly, remove rubbers from body mounting 
brackets.
10.Remove HO2S sensors from exhaust...

MANIFOLD AND EXHAUST SYSTEM - V8
REPAIRS 30-2-3
Front pipe  
$% 30.10.09 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove exhaust system.
 
 +  MANIFOLD AND EXHAUST SYSTEM 
- V8, REPAIRS, Exhaust system & 
mountings.
4.Remove HO2S sensors from exhaust 
assembly and discard sealing washers.
5.Using LRT-99-027,...

MANIFOLD AND EXHAUST SYSTEM - V8
30-2-4 REPAIRS
Intermediate pipe 
$% 30.10.12 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Using LRT-99-027, cut pipe at point indicated 
by depression in pipe.
4.Remove 4 nuts securing intermediate silencer 
mountings to body.
5.With assistance, remove intermediate exhaust...

MANIFOLD AND EXHAUST SYSTEM - V8
REPAIRS 30-2-5
Tail pipe & silencer 
$% 30.10.22
Remove
1.Position vehicle on lift.
2.Using LRT-99-027, cut pipe at point indicated 
by depression in pipe.
3.Remove 8 nuts securing mountings and  with 
assistance, remove tail pipe and silencer 
assembly.
4.Remove 4 exhaust mountings.
Refit
1.Fit 4 exhaust mountings.
2.Clean intermediate pipe and fit sleeve.3.With assistance, fit tail pipe and silencer 
assembly, locate mountings and fit nuts. 
Tighten nuts to 25 Nm (18...

MANIFOLD AND EXHAUST SYSTEM - V8
30-2-6 REPAIRS
Gasket(s) - inlet manifold  
$% 30.15.08 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Disconnect battery earth lead.
2.Remove air intake hose.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Hose - air flow meter to 
throttle body.
3.Remove LH ignition coil cover.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Cover - Ignition...

MANIFOLD AND EXHAUST SYSTEM - V8
REPAIRS 30-2-7
11.Disconnect multiplugs from KS and CMP 
sensor.
12.Remove 2 nuts securing fuel injector harness to 
fuel rail.
13.Release vacuum reservoir and mounting 
bracket from LH fuel injector harness securing 
stud.
14.Remove fuel hose and mounting bracket from 
LH fuel injector harness securing stud.
15.Release alternator harness from 2 clips on 
engine cover mounting brackets.16.Disconnect multiplugs from fuel injectors.
17.Release engine harness from clips and...