Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

ENGINE - V8
12-2-98 OVERHAUL
11.Compress LH exhaust timing chain tensioner, 
fit LRT-12-220 to chain tensioner and remove 2 
Torx bolts securing LH VCC unit and LH 
exhaust camshaft sprocket.
NOTE: Thread is left handed.
12.Remove LH exhaust camshaft gear, LH 
exhaust camshaft chain and LH VCC unit.
NOTE: Secure chain to cylinder head to 
prevent chain falling into lower timing gear 
cover.
Reassembly
1.Position LH VCC unit to timing gear chain, fit 
VCC unit and exhaust camshaft sprocket to 
camshafts,...

ENGINE - V8
OVERHAUL 12-2-99
8.Rotate RH VCC unit anticlockwise using LRT-
12-224 to 40 Nm (30 lbf.ft) and using the 
multimeter, check continuity is present.
NOTE: Rotating the VCC unit using LRT-12-
224 will remove the oil cushion and make sure 
the VCC unit is at the full LH stop position. 
Continuity should be present when the VCC 
unit reaches this position.
9.Tighten Torx bolts securing RH VCC unit and 
exhaust camshaft sprocket to 15 Nm (11 lbf.ft) 
and loosen one quarter of a turn.
NOTE: Thread...

ENGINE - V8
12-2-100 OVERHAUL
18.Position LRT-12-228/1 locating dowel to RH 
CMP sensor ring, fit 2 bolts securing tool to RH 
cylinder head and tighten.
NOTE: To ensure correct CMP sensor ring 
adjustment, make sure the tool  is aligned flush 
with the cylinder head and lower timing gear 
cover before tightening the tool securing bolts.
19.Tighten nut securing CMP sensor ring to 40 Nm 
(30 lbf.ft) and remove LRT-12-228/1 from RH 
cylinder head.
NOTE: Thread is left handed.
20.Fit LH CMP sensor ring, fit...

ENGINE - V8
OVERHAUL 12-2-101
Strainer - oil pick up 
$% 12.60.20.01
Remove
1.Remove lower sump gasket.
 
 +  Engine - V8, OVERHAUL, Gasket - 
sump bottom plate.
Disassembly
1.Remove 2 bolts securing oil pick-up strainer to 
oil pump, remove strainer and discard O ring.
Inspect
1.Clean oil pick up strainer and mating faces.
Reassembly
1.Fit new O ring to oil pump groove location, 
position oil pick-up strainer to oil pump.
2.Fit 2 bolts securing oil pick-up strainer to oil 
pump and tighten bolts to 10...

ENGINE - V8
12-2-102 OVERHAUL
4.Remove 2 nuts securing oil pump and remove 
the oil pump.
5.Remove oil feed and governing pipes from 
cylinder block, remove and discard 3 O rings.
6.Remove adjusting nut from oil pump.
Inspect
1.Clean oil pipes, oil pump and mating faces.
Reassembly
1.Lubricate new O rings. Fit oil feed pipe O 
rings to groove in pump and pipe and fit 
governing pipe O ring to pipe.
2.Fit oil pipes to cylinder block.
3.Fit adjusting nut fully into the oil pump.
4.Lubricate the oil pump....

ENGINE - V8
OVERHAUL 12-2-103
Gasket - sump bottom plate 
$% 12.60.37.01
Remove
1.Position container below engine sump drain 
plug, remove plug and discard sealing washer. 
Allow oil to drain.
2.Remove 21 bolts securing lower oil sump to 
upper oil sump. Remove lower oil sump and 
discard gasket.
Disassembly
1.
Inspect
1.
Reassembly
1.
Refit
1.Clean lower oil sump mating faces.
2.Fit new gasket to lower oil sump mating face.
3.Fit lower oil sump.4.Fit 21 bolts securing lower oil sump and tighten 
to 10...

ENGINE - V8
12-2-104 OVERHAUL
Gasket - oil sump
$% 12.60.38.01
Remove
1.Remove dipstick.
2.Remove 2 nuts securing dipstick tube bracket 
to camshaft cover.
3.Remove nut and clamp securing dipstick tube 
to oil sump. Remove dipstick tube and sealing 
washer. Discard O ring.4.Loosen 2 bolts securing ancillary drive belt 
tensioner and release tension from the belt.
5.Remove ancillary drive belt.
6.Remove 2 Allen bolts and one nut securing 
PAS pump, remove pump.
7.Remove oil pick-up strainer.
 
 +  Engine...

ENGINE - V8
OVERHAUL 12-2-105
Disassembly
1.Remove banjo bolt securing engine oil return 
pipe to oil sump and discard 2 sealing washers.
2.Remove banjo bolt securing engine oil filter 
return pipe to oil sump and discard 2 sealing 
washers.3.Remove 31 bolts securing oil sump to engine 
cylinder block.
NOTE: Note position of all bolts as they are 
different lengths;
lA=M8 x 60mm
lB=M6 x 80mm
lC=M6 x 40mm.
lAll remaining bolts are M6 x 20mm.
4.Remove oil sump and discard gasket.
Inspect
1.Clean oil sump...

ENGINE - V8
12-2-106 OVERHAUL
Reassembly
1.Apply a 2 mm bead of sealant to areas 
illustrated.
2.Fit new gasket, position oil sump to cylinder 
block, fit bolts but do not tighten at this stage.
NOTE: Note position of 6 mm bolts as they are 
two different lengths.
3.Tighten 31 bolts securing upper oil sump to 
cylinder block ,M6 x 8.8mm to 10 Nm (7 lbf.ft), 
M6 x 10.9mm to 12 Nm (9 lbf.ft) and M8 x 
8.8mm to 22 Nm (16 lbf.ft).
4.Clean engine oil filter and return pipe mating 
faces.
5.Fit 2 new sealing...

ENGINE - V8
OVERHAUL 12-2-107
5.Remove bolt securing SAI pipe to LH cylinder 
head.
6.Remove Allen bolt securing secondary air 
injection SAI pipe clip to coolant pump.
7.Release SAI pipe from cylinder heads and 
position aside, discard O rings.
Disassembly
1. RH upper timing gear cover: Remove 2 bolts 
securing VCC solenoid seal and remove seal.2. RH upper timing gear cover: Remove chain 
tensioner from timing gear cover and discard 
sealing washer.
3. RH upper timing gear cover: Separate chain...