Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

MAINTENANCE
10-18 PROCEDURES
Exhaust system
Check
1.Check for signs of exhaust system leaks, 
damage and security.
Underbody
Check
1.Check all visible areas for corrosion.
Body
Check
1.Check all visible areas (excluding body 
cavities) for corrosion.
Steering rod ball joints and dust covers
Check
1.Check condition of ball joints and dust covers 
and security of fixings.
M01 0303 

MAINTENANCE
PROCEDURES 10-19
Road/roller test
WARNING: Roller test must be restricted to 3 
mph (5 km/h). If 2 wheel rolling road is to be used, 
disconnect propeller shaft from the transfer box 
output shaft driving the axle which is NOT on the 
rolling road.
Testing
1.Check for correct operation of starter switch, 
ensure engine starts correctly; leave the engine 
running.
2.With vehicle stationary, turn steering from lock 
to lock. Check for smooth operation and ensure 
there is no undue noise from...

MAINTENANCE
10-20 PROCEDURES 

ENGINE - V8
ADJUSTMENTS 12-2-1
Engine  - V 8 ADJUST ME NTS
Engine oil pressure check 
$% 12.90.09.01 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Check
1.Disconnect battery earth lead.
2.Remove oil pressure switch.
 
 +  Engine - V8, REPAIRS, Switch - oil 
pressure.
3.Fit LRT-12-052/10 to oil filter housing and fit 
LRT-12-052C to LRT-12-052/10, tighten 
unions.
4.Check engine oil...

ENGINE - V8
12-2-2 ADJUSTMENTS 

ENGINE - V8
REPAIRS 12-2-3
REPAIRS
Pulley - crankshaft 
$% 12.21.01 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Remove ancillary drive belt
 
 +  CHARGING AND STARTING, 
REPAIRS, Ancillary drive belt - V8.
4.Remove viscous fan.
 
 +  COOLING SYSTEM - V8, REPAIRS, 
Coupling unit - viscous fan.
5.Remove compressor...

ENGINE - V8
12-2-4 REPAIRS
8.Fit LRT-12-230/1 and LRT-12-230/2 to 
crankshaft seal and remove crankshaft oil seal.
9.Discard oil seal.
Refit
1.Clean seal mating faces.
2.Fit new crankshaft oil seal to front cover using 
LRT-12-231.
NOTE: Front crankshaft oil seal should be fitted 
flush to front timing cover.
3.Remove LRT-12-231.
4.Clean crankshaft pulley hub and mating faces, 
fit crankshaft pulley hub to crankshaft.
5.Fit new bolt to crankshaft, lock crankshaft using 
LRT-12-229 and initially tighten...

ENGINE - V8
REPAIRS 12-2-5
2.Fit LRT-12-217 and LRT-12-179 to new 
crankshaft rear oil seal and fit new seal to 
housing.
3.Check for correct fitment of dowels in cylinder 
block.
4.Fit new gasket to crankshaft rear oil seal 
housing.
5.Apply sealant , Part No. STC 50550 to upper oil 
sump gasket contact point.6.Fit LRT-12-218 to crankshaft. Apply a thin coat 
of oil to inner lip of crankshaft rear oil seal, fit 
seal and housing over LRT-12-218, fit onto 
dowels and remove tool.
7.Fit new washers to 6...

ENGINE - V8
12-2-6 REPAIRS
Gasket - cylinder head - LH 
$% 12.29.02 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Position vehicle on lift.
2.Disconnect battery earth lead.
3.Drain cooling system.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
4.Drain engine oil and remove oil filter.
 
 +  MAINTENANCE, PROCEDURES, 
Engine oil and filter - V8...

ENGINE - V8
REPAIRS 12-2-7
12.Working in the sequence shown, progressively 
loosen 10 cylinder head bolts.
13.Discard 10 cylinder head bolts and remove 10 
cylinder head bolt washers.
14.With assistance, remove cylinder head 
assembly.
15.Discard cylinder head gasket.
16.Discard O ring from cylinder block.Refit
1.Clean mating faces of cylinder head and 
cylinder block, dowels and dowel holes. If 
necessary remove all traces of sealing 
compound with hard wood scraper. Ensure 
remnants do not remain in...