Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

MAINTENANCE
10-8 PROCEDURES
Brake fluid
Replace
1.Replace brake fluid.
 
 +  BRAKES, ADJUSTMENTS, Brake 
system bleeding.
Fuel filter element - Td6 engine
Replace
1.Replace fuel filter element. 
 
 +  FUEL DELIVERY SYSTEM - Td6, 
REPAIRS, Filter. 

MAINTENANCE
PROCEDURES 10-9
Anti-freeze
Replace
1.Replace anti-freeze. 
 
 +  COOLING SYSTEM - Td6, 
ADJUSTMENT, Coolant - drain and refill.
 
 +  COOLING SYSTEM - V8, 
ADJUSTMENTS, Coolant - drain, flush & 
refill.
Cooling system
Check and top-up
1.Check coolant level, top-up if necessary.
2.With engine cold, remove expansion tank filler 
cap.
3.Top-up with recommended mixture of coolant 
and anti-freeze until float is at its highest 
position in the filler neck.
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS...

MAINTENANCE
10-10 PROCEDURES
Spark plugs - V8 engine
Replace
Take great care when fitting spark plugs not 
to cross-thread plug, otherwise costly 
damage to cylinder heads will result. It is 
essential that only the correct grade of 
spark plugs, approved for this engine are 
fitted. Incorrect grade of spark plugs may 
lead to piston overheating and engine 
failure. 
1.Disconnect battery earth lead.
2.Remove ignition coils.
 
 +  ENGINE MANAGEMENT SYSTEM - 
V8, REPAIRS, Ignition coils - multiple - set....

MAINTENANCE
PROCEDURES 10-11
Ancillary drive belt
Check
Td6 ancillary drive belt
1.Check ancillary drive belt for signs of splits, 
fraying, oil contamination and wear.
V8 ancillary drive belt
2.Check ancillary drive belt for signs of splits, 
fraying, oil contamination and wear.
Fluid reservoirs
Check/top-up – Brake fluid reservoir
1.Check fluid level in brake fluid reservoir.
2.Clean area around filler cap, remove cap. 
3.Top-up if necessary to correct level on reservoir 
using recommended fluid.
 
 +...

MAINTENANCE
10-12 PROCEDURES
V8 engine
2.
V8 engine - Check fluid level in PAS fluid 
reservoir.
3.
All engines - Clean area around filler cap, 
remove cap.
4.Top-up if necessary to highest level mark on 
dipstick using recommended fluid. 
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, Fluids.
5.Fit filler cap.
Check/top-up – Screen and headlamp washer 
reservoir
1.Check fluid level in washer reservoir.
2.Clean area around filler cap, remove cap.
3.Top-up if necessary to top of reservoir filler...

MAINTENANCE
PROCEDURES 10-13
Engine oil and filter - Td6 engine
WARNING: Avoid excessive skin contact with 
used engine oil. Used engine oil contains 
potentially harmful contaminants which may 
cause skin cancer or other serious skin 
disorders.
Replace
1.Raise vehicle on ramp.
2.Position suitable container beneath sump.
3.Clean area around oil drain plug.
4.Remove oil drain plug, discard sealing washer.
5.Allow oil to drain.
WARNING: Observe due care when draining 
oil as oil can be very hot.
6.Lower...

MAINTENANCE
10-14 PROCEDURES
19.Fill engine with recommended grade of oil to 
correct mark on dipstick. 
 
 +  CAPACITIES, FLUIDS, 
LUBRICANTS AND SEALANTS, 
Lubrication.
20.Start engine, run at idle until oil pressure light is 
extinguished.
21.Stop engine, recheck oil level.
22.Check for signs of oil leakage.
Engine oil and filter - V8 engine
WARNING: Avoid excessive skin contact with 
used engine oil. Used engine oil contains 
potentially harmful contaminants which may 
cause skin cancer or other...

MAINTENANCE
PROCEDURES 10-15
9.Remove and discard sealing ring from centre 
spindle.
10.Clean filter housing and cap.
11.Lubricate new O ring and sealing ring with 
engine oil and fit to cap and centre spindle.
12.Fit new filter element ensuring that large 
diameter hole in centre of element is towards 
bottom of filter housing.
13.Fit oil filter cap  and tighten to 25 Nm (18 lbf.ft).
14.Raise vehicle on ramp.
15.Fit new sealing washer to oil drain plug.
16.Fit oil drain plug and tighten to 23 Nm (17...

MAINTENANCE
10-16 PROCEDURES
Gearbox fluid - V8 
Check/top-up
1.Position vehicle on lift.
2.Apply handbrake and position chocks under 
front and rear wheels.
3.Connect TestBook/T4 to monitor gearbox fluid 
temperature.
CAUTION: The gearbox fluid level must only 
be checked when the temperature of the 
fluid is between 30° C and 40° C. The 
reading obtained will be incorrect if the fluid 
is outside this temperature range.
4.Start engine, move selector lever from P 
through all gear positions, pausing in...

MAINTENANCE
PROCEDURES 10-17
Brake  hose, brake pipes, fuel pipes, 
hydraulic pipes and unions/electrical 
harnesses
Check - general
1.Check brake servo hose for cracks, leaks and 
chafing.
2.Check brake pipes and unions for chafing, 
leaks and corrosion and  that all pipes and 
hoses are correctly routed and secure.
3.Check electrical harnesses for chafing and 
damage.
Check – Td6/V8 engine fuel pipes
1.Check visible fuel pipes and unions for chafing, 
leaks and corrosion and that all pipes and 
hoses...