Konica Minolta bizhub 500 User Manual

3Specifying Settings From the Control Panel
3-76 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area. Otherwise, cancel the Utility mode by touching [Close] in each 
screen until the screen for the Copy, Fax, Scan or Box mode appears.
2
Reminder 
If the LDAP server settings are not specified correctly, network failure 
may occur. The server...

Specifying Settings From the Control Panel3
bizhub 500/420 3-77
Specifying Settings From the Control Panel
Chapter 3
3.19 Setting Up LDAP Settings
The LDAP server can be registered and authentication settings can be spec-
ified.
LDAP Server Registration Parameters
The LDAP server registration parameters are as follows:
Setting Up LDAP screen 1/6
Setting Up LDAP screen 2/6
* When [LDAP Function] is set to “ON” on the Enabling LDAP screen, the [Check Connection] key 
is displayed only when [Manual...

3Specifying Settings From the Control Panel
3-78 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Setting Up LDAP screen 3/6
Setting Up LDAP screen 4/6
Setting Up LDAP screen 5/6
ItemDescription
Enable SSL Sets whether to use SSL (data encryption) when 
connecting to the LDAP server. When SSL is used, the 
content that is sent is encrypted.
Port No. Sets the port number of the LDAP server. To change the 
value, press the [C] (clear) key, and then use the keypad to 
type in the value...

Specifying Settings From the Control Panel3
bizhub 500/420 3-79
Specifying Settings From the Control Panel
Chapter 3
Setting Up LDAP screen 6/6
Use referral Select whether to use the referral setting. When referral is 
used, the search base that was specified in LDAP Sever 
Setting searches the top and bottom levels as the starting 
point.
ItemDescription
ItemDescription
Login Name Sets the login name used to connect to the LDAP server. 
Use the keyboard that appears in the touch panel to type in 
the...

3Specifying Settings From the Control Panel
3-80 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
To specify Setting Up LDAP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [8 LDAP Setting].
3In the LDAP Setting screen, touch [2 Setting Up LDAP].
4Touch the LDAP server button to register and specify the setting.
Setting Up LDAP screen 1/6 appears.
5Specify the desired settings.
6Touch...

Specifying Settings From the Control Panel3
bizhub 500/420 3-81
Specifying Settings From the Control Panel
Chapter 3
7Specify the desired settings.
8Touch [Fwd.→].
Setting Up LDAP screen 3/6 appears.
9Specify the desired settings.
10Touch [Fwd.→].
Setting Up LDAP screen 4/6 appears.
11Specify the desired settings.
12Touch [Fwd.→].
Setting Up LDAP screen 5/6 appears.
Downloaded From ManualsPrinter.com Manuals 

3Specifying Settings From the Control Panel
3-82 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
13Specify the desired setting.
14Touch [Fwd.→].
Setting Up LDAP screen 6/6 appears.
15Specify the desired settings.
16Touch [OK].
The LDAP server registration and authentication are set.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the...

Specifying Settings From the Control Panel3
bizhub 500/420 3-83
Specifying Settings From the Control Panel
Chapter 3
2
Note 
Be sure to use an authentication method like the one that is used by the 
LDAP server. For details, refer to the manual of the LDAP server being 
used.
If the authentication method is specified as “GSS-SPNEGO”, enter the 
domain name for “Active Directory”.
!
Detail 
Depending on the authentication method, settings for the following pa-
rameters must be set correctly on the Setting...

3Specifying Settings From the Control Panel
3-84 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Initial Setting for Search Details
The initial setting of the search conditions when performing a detailed search 
can be specified by “Name”, “E-Mail”, “Fax Number”, “Last Name”, “First 
Name”, “City”, “Company Name”, and “Department”.
1On the Setting Up LDAP screen, touch [Initial Setting for Search De-
tails].
The Initial Setting for Search Details screen appears.
2Touch [Condition]....

Specifying Settings From the Control Panel3
bizhub 500/420 3-85
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals