Konica Minolta bizhub 500 User Manual

3Specifying Settings From the Control Panel
3-106 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.26 Total Counter Report Setting
You can specify the total counter notification schedule and notification des-
tination.
The settings that can be specified in the total counter screen are described 
below.
To specify the total counter report settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail...

Specifying Settings From the Control Panel3
bizhub 500/420 3-107
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears....

3Specifying Settings From the Control Panel
3-108 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
When “Weekly” is specified as the notification period
When “Monthly” is specified as the notification period
ItemDescription
Interval of Week(s) Enter the interval of weeks for sending the schedule. To 
change the value, press the [C] (clear) key, and then use the 
keypad to type in the value (between 1 and 6).
Day of the Week Select the day of the week for sending the schedule....

Specifying Settings From the Control Panel3
bizhub 500/420 3-109
Specifying Settings From the Control Panel
Chapter 3
To specify the notification address settings
1In the Total Counter Report Setting screen, touch [Schedule1].
The Schedule1 setting screen appears.
2Specify the notification period.
3Touch [OK].
The Total Counter Report Setting screen appears again.
2
Note 
To cancel changes to the setting, touch [Cancel].
Notification Address Setting
You can specify the e-mail addresses for sending the...

3Specifying Settings From the Control Panel
3-110 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
5Select whether you want to use this schedule to send to this address.
6Touch [OK], and then touch [OK] in the next screen that appears.
The Total Counter Report Setting screen appears again.
2
Note 
To cancel changes to the setting, touch [Cancel].
Downloaded From ManualsPrinter.com Manuals 

Specifying Settings From the Control Panel3
bizhub 500/420 3-111
Specifying Settings From the Control Panel
Chapter 3
3.27 PING Confirmation
Settings for checking the TCP/IP network using PING can be specified.
PING Confirmation Parameters
The PING Confirmation parameters are as follows:
To specify PING confirmation settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail...

3Specifying Settings From the Control Panel
3-112 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
5Touch [Close].
2
Note 
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area. Otherwise, cancel the Utility mode by touching [Close] in each 
screen until the screen for the Copy, Fax, Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 

Specifying Settings From the Control Panel3
bizhub 500/420 3-113
Specifying Settings From the Control Panel
Chapter 3
PING TX Address
The host address of the device to ping can be specified.
1In the PING Confirmation screen, touch [Host Address].
The Host Address screen appears.
2Touch [IP Address Input] or [Host Name Input].
– To specify the host address with the IP address, touch [IP Address 
Input].
– To specify the host address with the host name, touch [Host Name 
Input].
– If selecting [Host Name...

3Specifying Settings From the Control Panel
3-114 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
!
Detail 
For the procedure to enter characters using the keyboard that appears 
on the screen, refer to “Entering text” on page 6-5.
Downloaded From ManualsPrinter.com Manuals 

Specifying Settings From the Control Panel3
bizhub 500/420 3-115
Specifying Settings From the Control Panel
Chapter 3
3.28 SLP Settings
The use of SLP can be enabled or disabled. If set to “Enable”, devices can 
be searched using TWAIN. If set to “Disable”, device cannot be searched.
To specify SLP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail Setting screen, touch...