Konica Minolta bizhub 500 User Manual

3Specifying Settings From the Control Panel
3-126 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
v3 Setting
The settings that can be specified are described below.
SNMP v3 Setting screen 1/3
SNMP v3 Read Setting screen 2/3
SNMP v3 Write Setting screen 3/3
ItemDescription
Context Name Specify the context name. Use the keyboard that appears 
in the touch panel to type in the context name (up to 63 
characters).
Discovery User Select whether to enable the Discovery User setting....

Specifying Settings From the Control Panel3
bizhub 500/420 3-127
Specifying Settings From the Control Panel
Chapter 3
To specify the v3 settings
1In the Network Setting screen, touch [v3 Setting].
SNMP v3 Setting screen 1/3 appears.
2Specify the desired settings.
3Touch [Fwd.→].
SNMP v3 Setting screen 2/3 appears.
4Specify the desired settings.
5Touch [Fwd.→].
SNMP v3 Setting screen 3/3 appears.
Downloaded From ManualsPrinter.com Manuals 

3Specifying Settings From the Control Panel
3-128 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
6Specify the desired settings.
7Touch [OK].
The SNMP Setting screen appears again.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode...

Specifying Settings From the Control Panel3
bizhub 500/420 3-129
Specifying Settings From the Control Panel
Chapter 3
3.33 Bonjour Setting
You can specify the Bonjour setting.
Bonjour Setting screen
To specify the Bonjour settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network Setting screen, touch [Fwd.→], and then touch [2 Bon-
jour Setting].
The Bonjour Setting screen appears.
3Specify the desired settings.
4Touch [OK].
ItemDescription
Bonjour  Setting Select whether...

3Specifying Settings From the Control Panel
3-130 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for...

Specifying Settings From the Control Panel3
bizhub 500/420 3-131
Specifying Settings From the Control Panel
Chapter 3
3.34 TCP Socket Setting
You can specify the TCP socket settings. The TCP socket is used for the 
computer programs and the data transmission of this machine.
The settings that can be specified are described below.
TCP Socket Setting screen 1/2
TCP Socket Setting screen 2/2
To specify the TCP socket settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network...

3Specifying Settings From the Control Panel
3-132 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
4Touch [Fwd.→].
TCP Socket Setting screen 2/2 appears.
5Specify the desired settings.
6Touch [OK].
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the...

Specifying Settings From the Control Panel3
bizhub 500/420 3-133
Specifying Settings From the Control Panel
Chapter 3
3.35 OpenAPI Settings
Specify whether or not interface is open to software with a function for com-
municating with the copier. The settings for “Access Setting”, “Port No.”, 
“SSL”, and “Authentication” of OpenAPI can be changed.
Access Setting
Sets whether to permit access from other systems that use OpenAPI. (De-
fault setting: Allow)
1In the Administrator Setting screen, touch [System...

3Specifying Settings From the Control Panel
3-134 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Port No.
Specify the port number that other systems access using OpenAPI (initial 
port number: 50001, initial port number (SSL): 50003).
1In the Administrator Setting screen, touch [System Connection]. (Refer 
to page 3-8 for more details.)
2In the System Connection screen, touch [1 OpenAPI Setting].
3In the OpenAPI Setting screen, touch [Port No.].
The OpenAPI Port Setting screen...

Specifying Settings From the Control Panel3
bizhub 500/420 3-135
Specifying Settings From the Control Panel
Chapter 3
SSL
Specify whether to encrypt with SSL access from other systems that use 
OpenAPI. (Default setting: OFF)
1In the Administrator Setting screen, touch [System Connection]. (Refer 
to page 3-8 for more details.)
2In the System Connection screen, touch [1 OpenAPI Setting].
3In the OpenAPI Setting screen, touch [SSL].
4Touch the desired key.
SSL encryption is enabled or disabled.
2
Note 
To...