Konica Minolta bizhub 500 User Manual

3Specifying Settings From the Control Panel
3-46 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.12 TCP/IP Settings
The settings for using the machine on a TCP/IP network can be specified.
To activate all network setting changes, turn the main power off and then 
back on.
2
Reminder 
When turning the main power switch OFF then ON, wait for 10 seconds 
or longer before turning it ON again; otherwise the copier may not func-
tion normally.
Before Specifying the Settings
When...

Specifying Settings From the Control Panel3
bizhub 500/420 3-47
Specifying Settings From the Control Panel
Chapter 3
Items To Be Specified
The following items are specified.
TCP/IP Setting screen 1/5
TCP/IP Setting screen 2/5
TCP/IP Setting screen 3/5
TCP/IP Setting screen 4/5
ItemDescription
TCP/IP Setting Specify whether to turn on the TCP/IP settings.
ItemDescription
IP Address Setting Method Select whether to directly input a fixed IP address or to au-
tomatically acquire an IP address.
IP  Address...

3Specifying Settings From the Control Panel
3-48 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
TCP/IP Setting screen 5/5
2
Note 
Be sure to enter the host name and domain name so that the total 
number of characters entered is within 254 characters.
To specify TCP/IP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [2 TCP/IP Setting].
TCP/IP Setting screen 1/5 appears.
3Specify the...

Specifying Settings From the Control Panel3
bizhub 500/420 3-49
Specifying Settings From the Control Panel
Chapter 3
– If [Auto Input] was selected under “IP Address Setting Method”, 
specify the automatic acquisition procedure, and then touch [OK].
6Touch [Fwd.→].
TCP/IP Setting screen 3/5 appears.
7Specify the desired settings.
8Touch [Fwd.→].
TCP/IP Setting screen 4/5 appears.
Downloaded From ManualsPrinter.com Manuals 

3Specifying Settings From the Control Panel
3-50 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
9Specify the desired settings.
10Touch [Fwd.→].
TCP/IP Setting screen 5/5 appears.
11Specify the desired settings.
12Touch [OK].
The TCP/IP settings are applied.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching...

Specifying Settings From the Control Panel3
bizhub 500/420 3-51
Specifying Settings From the Control Panel
Chapter 3
IP Filtering
The IP addresses in the specified ranges can be permitted or denied.
IP addresses can connect depending on whether “Enable” or “Disable” has 
been selected for “Permit Access” and “Deny Access” in the IP Filtering 
screen, as shown below.
1In TCP/IP Setting screen 5/5, touch [IP Filtering].
The IP Filtering > Permit Access screen appears.
2Touch [Enable] or [Disable] under...

3Specifying Settings From the Control Panel
3-52 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3Touch the button for a set (Set 1 to Set 5), and then use the keypad to 
type in the address range.
– The range setting cannot include “0.0.0.0”. For example, to specify 
all addresses before 192.168.1.20, specify the range from 0.0.0.1 to 
192.168.1.20.
– Touch [Deny Access] to specify the IP addresses to refuse access. 
The procedure for setting the IP addresses is the same as on the...

Specifying Settings From the Control Panel3
bizhub 500/420 3-53
Specifying Settings From the Control Panel
Chapter 3
RAW Port No.
Specify the RAW port numbers used by the printer. By specifying multiple 
port numbers, multiple data can be accepted simultaneously.
1In TCP/IP Setting screen 5/5, touch [RAW Port No.].
The RAW Port Number screen appears.
2Touch the button for the desired port.
3Touch [ON] or [OFF].
4To use the selected port, press the [C] (clear) key to erase the value, 
and then use the...

3Specifying Settings From the Control Panel
3-54 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.13 NetWare Settings
The settings for using the machine on a NetWare network can be specified.
NetWare Parameters
The NetWare settings are as follows:
NetWare Setting screen 1/5
NetWare Setting screen 2/5
NetWare Setting screen 3/5
NetWare Setting screen 4/5
ItemDescription
IPX Setting Specify whether to use IPX.
Ethernet Frame Type Sets the frame type that is used for communications....

Specifying Settings From the Control Panel3
bizhub 500/420 3-55
Specifying Settings From the Control Panel
Chapter 3
NetWare Setting screen 5/5
To specify NetWare settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [3 NetWare Setting].
NetWare Setting screen 1/5 appears.
3Specify the desired settings.
4Touch [Fwd.→].
NetWare Setting screen 2/5 appears.
NDS Context Name Sets the NDS context name. Use the...