Key System U.S. Atlas Avm Jr Installation Programming Instruction Manual

							 
Atlas AVM JR. Installation and Programming Manual 11-1 11. APPENDIX E  
E.1 E.1   KSX KSX- -32/64/128/256 Detailed Programming 32/64/128/256 Detailed Programming   
E.1.1 Programming Voicemail Ports 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: M:. 
     Enter Mode No. 
2. Enter Mode 03 by dialing 03 
3. Enter the first port number that you are attaching to the voicemail. (01-32 for 
KSX-32, 0-64 for KSX-64, 001-128 for KSX-128 and 001-256 for KSX-256) 
4. Dial 5 to select the Voice Mail Port option. 
5. Press the FLASH key followed by the CONF key followed by the 
HOLD” key.  (Only do this for the first time not on the following ports). 
6. Press the MSG key followed by the HOLD key to enable the port as a 
voicemail port. 
The display should show the following: M:03  XX  5   YES 
     VOICE MAIL PORT 
 
7. Press the DATA key and then follow the above steps for the rest of your 
voicemail ports.  (Be sure to exclude step 5). 
8. Press the RLS key to exit out of programming. 
 
E.1.2 Programming the Station Group 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD.  
						

							Appendix E  11-2 Atlas AVM JR. Installation and Programming Manual The display should show the following: M:. 
     Enter Mode No. 
2. Enter mode 67 by dialing 67” 
3. Dial the station group number you wish to assign your voicemail to (1-8). 
4. Dial the first position number of that station group (1 for KSX-32 and 01 for 
KSX-64/128/256). 
5. Dial the port number of the first port of voicemail. 
The display should show the following: M:67  XX  XX   XX 
     ST HUNT GROUP 
 
6. Press the HOLD” key followed by the TRF key to save the entry and 
move to the next position in the group. 
7. Dial the next port number being used for voicemail and repeat STEP 6 until 
you have entered all your ports (be sure to press HOLD after your last port 
is entered). 
8. Press the RLS key to exit out of programming. 
E.1.3 Programming Direct Ring 
Use this programming procedure to program the voicemail to answer all incoming 
calls immediately. 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: M:. 
     Enter Mode No. 
2. Enter mode number (39 for Day ringing or 40 for Night ringing) 
3. Enter the trunk number that you wish to have the voicemail answer (1-8 on 
KSX-32 or 01-24 on KSX-64/128/256). 
4. Enter the station group number that you assigned to the voicemail (1-8). 
 
  
						

							 Appendix E Atlas AVM JR. Installation and Programming Manual 11-3 The display should show the following: M:39  1  1 
     ST GP RING - DAY 
  or 
     M:40  1  1 
     ST GP RING - NIT 
5. Press the HOLD key to save changes. 
6. Press the DATA key and repeat steps 1-6 until you have entered all the 
trunks that you wish to ring immediately to voicemail. 
7. Press the RLS key when finished. 
E.1.4  Programming Delayed Ringing 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: M:. 
     Enter Mode No. 
 
2. Enter mode number by dialing 47 for day or 48 for night. 
3. Enter the first position of common ring by dialing 01. 
The display should show the following: M:47  01 
     COMM RING - DAY 
 
4. Press the MSG” key to program a station group. 
5. Dial the station group number that you assigned your voicemail to (1-8) 
6. Press the HOLD key to save your changes. 
7. Press the DATA key to enter a new mode number. 
8. Enter mode number 46 by dialing 46. 
9. Enter the time in seconds that you wish to have the voicemail delay answer. 
NOTE: When programming on the KSX-64/128/256 with version 400 software 
you must enter a trunk number before you enter the delay time.  This  
						

							Appendix E  11-4 Atlas AVM JR. Installation and Programming Manual value can be from 01-24.  This will allow you to program certain 
trunks for a longer delay. 
10. Press the HOLD key to save your programming. 
11. Press the RLS key to exit programming. 
E.2 E.2   KDX KDX- -500 Detailed Programming 500 Detailed Programming   
E.2.1 Programming Voicemail Ports 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: PROGRAM SECTION 
      
2. Enter the Station Programming section by dialing 2. 
3. Enter the Voicemail port Programming mode by dialing 34. 
4. Enter your first port of voicemail (001-400). 
5. Press the FLASH” key followed by the CONF followed by the 
HOLD key to clear out any existing ports as voicemail ports.  (Do this 
step only for the first port of voicemail.) 
6. Press the MSG key followed by the HOLD key to activate that port 
as a voicemail port. 
7. Press the DATA key and repeat steps 2-6 until all of your voicemail 
ports are programmed.  (Be sure not to follow step 5, as this will erase 
the programming you have just done.) 
8. Press the RLS key when you are finished 
E.2.2 Programming the Station Hunt Group 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
  
						

							 Appendix E Atlas AVM JR. Installation and Programming Manual 11-5 The display should show the following: PROGRAM SECTION 
      
 
2. Enter System Programming mode by dialing 3. 
3. Enter Voicemail Station Hunt Group mode by dialing 50. 
4. Enter the first position of the hunt group by dialing 01. 
5. Enter your first port of voicemail (001-400). 
6. Press the HOLD key to save that port. 
7. Press the TRF key to move to the next position in that hunt group. 
8. Enter your next port of voicemail (001-400). 
9. Repeat steps 6-8 until all of your voicemail ports are programmed in your 
hunt group. 
10. Press the RLS key to exit out of programming when you are finished. 
E.2.3 Programming Direct Ringing 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: PROGRAM SECTION 
      
 
2. Enter Trunk Programming mode by dialing 1. 
3. Enter Trunk Station Hunt Group Ringing mode (65 for day or 66 for night). 
4. Enter Trunk Number to program for direct ringing (01-96) 
5. Press the 9 key to assign this trunk to ring station group 9 (this is your 
voicemail group). 
6. Press the HOLD key to save changes.  
						

							Appendix E  11-6 Atlas AVM JR. Installation and Programming Manual 7. You can either press the TRF key to advance to the next trunk and repeat 
steps 5-6 or you may press the DATA key and repeat steps 3-6 until all 
of the trunks you wish to ring directly to voicemail are programmed. 
8. Press the RLS key when you have finished programming. 
E.2.4  Programming Delayed Ringing 
1. Enter system programming from any display telephone by dialing PROG, 
PROG, 1, 2, 3, HOLD. 
The display should show the following: PROGRAM SECTION 
      
2. Enter Trunk Programming Mode by dialing 1. 
3. Enter Common Ring Mode (74 for day or 76 for night). 
4. Enter the first programming position by dialing 01. 
5. Press the MSG key to program a station group. 
6. Press the 9 key to enter your voicemail station group. 
7. Press the HOLD key to save your programming. 
8. Press the DATA key to enter a new mode number. 
9. Enter the Common Ring Delay mode corresponding to the programming 
you just saved (73 for day or 75 for night). 
10. Enter the trunk number that you wish to delay ring to voicemail (01-96). 
11. Enter the time in seconds that you wish the delay to be. 
12. Press the HOLD key to save your programming. 
13. Press the TRF key to go to the next trunk and then follow steps 11 and 
12 or press the DATA key and follow steps 9-12. 
14. Press the RLS key when you are finished programming.