HP P3015 Service Manual
Have a look at the manual HP P3015 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
H Face up detect sensorTest the rear cover open sensor (PS1) 1.Open the rear door until it stops to activate the sensor. Figure 3-10 Test the rear cover open sensor 2.Check the control-panel display for sensor response. 3. If there is no response, replace the rear cover open sensor. ENWW Tools for troubleshooting 147
I Cartridge-door open switchTest the cartridge-door open switch (SW501) 1.Open the cartridge door to activate the sensor. Figure 3-11 Test the cartridge-door open switch 2.Check the control-panel display for sensor response. 3. If there is no response, make sure that the sensor-actuator tab on the door is not damaged or missing. If necessary, replace the cartridge-door switch. 148 Chapter 3 Solve problems ENWW
J Rear cover open sensorTest the face-up detect sensor (PS8001) 1.Open the rear door, and then gently pull down on the door and lower the door until it is fully open to activate the sensor. NOTE:Figure 3-13 Test the face-up detect sensor (2 of 2) on page 149 shows the location of the face-up detect sensor (PS8001) behind the left cover. Figure 3-12 Test the face-up detect sensor (1 of 2) Figure 3-13 Test the face-up detect sensor (2 of 2) 2. Check the control-panel display for sensor response. 3. If there is no response, make sure that the sensor-actuator tab on the door is not damaged or missing. If necessary, replace the face-up detect sensor. ENWW Tools for troubleshooting 149
K Tray 1 paper sensorTray 1 (multipurpose tray) media-presence sensor (PS205) 1.Push the sensor lever toward the right side of the product and hold it there for 3 seconds to activate the sensor. Figure 3-14 Test the Tray 1 (multipurpose tray) media-presence sensor 2.Check the control-panel display for sensor response. 3. If there is no response, replace the multipurpose sensor PCA. 150 Chapter 3 Solve problems ENWW
L Tray 2 paper sensorTray 2 cassette media-presence sensor (PS3) 1.Remove the Tray 2 cassette, and then push on the sensor levers to activate the sensor. Figure 3-15 Test the Tray 2 cassette media-presence sensor 2.Check the control-panel display for sensor response. 3. If there is no response, replace the unit. ENWW Tools for troubleshooting 151
M Tray 2 detect switchTray 2 cassette presence switch (SW235) 1.Remove the Tray 2 cassette, and then install it to activate the sensor. Figure 3-16 Test the Tray 2 cassette presence switch 2.Check the control-panel display for sensor response. 3. If there is no response, make sure that the sensor-actuator tab on the cassette is not damaged or missing. If necessary, replace the switch. 152 Chapter 3 Solve problems ENWW
N Tray 3 paper sensorTray 3 media-presence sensor (PS451) 1.Remove the Tray 3 cassette, and then push on the sensor levers to activate the sensor. Figure 3-17 Test the Tray 3 cassette media-presence sensor 2.Check the control-panel display for sensor response. 3. If there is no response, replace the optional 500-sheet feeder. ENWW Tools for troubleshooting 153
O Tray 3 detect switchTray 3 cassette presence switch (SW461) 1.Remove the Tray 3 cassette, and then install it to activate the sensor. Figure 3-18 Test the Tray 3 cassette presence switch 2.Check the control-panel display for sensor response. 3. If there is no response, make sure that the sensor-actuator tab on the cassette is not damaged or missing. If necessary, replace the optional 500-sheet feeder. 154 Chapter 3 Solve problems ENWW
P Tray 4 paper sensorTray 4 media-presence sensor (PS451) 1.Remove the Tray 4 cassette, and then push on the sensor levers to activate the sensor. Figure 3-19 Test the Tray 4 cassette media-presence sensor 2.Check the control-panel display for sensor response. 3. If there is no response, replace the optional 500-sheet feeder. ENWW Tools for troubleshooting 155
Q Tray 4 detect switchTray 4 cassette presence switch (SW461) 1.Remove the Tray 4 cassette, and then install it to activate the sensor. Figure 3-20 Test the Tray 4 cassette presence switch 2.Check the control-panel display for sensor response. 3. If there is no response, make sure that the sensor-actuator tab on the cassette is not damaged or missing. If necessary, replace the optional 500-sheet feeder. 156 Chapter 3 Solve problems ENWW