HP P3015 Service Manual
Have a look at the manual HP P3015 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Tray 1 (multipurpose tray) separation pad CAUTION:Do not touch the surface of the pad. Skin oils deposited on the roller might cause paper- handling problems. 1. Press the cartridge-door release button, and then open the cartridge door. Make sure that the door is completely open. Figure 2-62 Remove the Tray 1 (multipurpose tray) separation pad (1 of 2) 2.Release two tabs (callout 1), and then remove the separation pad. Figure 2-63 Remove the Tray 1 (multipurpose tray) separation pad (2 of 2) 1 ENWW Removal and replacement procedures 87
Tray 2, Tray 3, or Tray 4 pickup roller CAUTION:Do not touch the surface of the roller. Skin oils deposited on the roller might cause print- quality problems. NOTE: If you did not remove the Tray 2, Tray 3, or Tray 4 cassette before servicing the product, remove it now. 1. Carefully place the product front-side up, so that you can see into the opening where the cassette would be installed. NOTE: Debris can scratch or damage the back of the product. Before you place the product front- side up, remove any debris from the work surface. If possible, set the product on a clean, dry cloth to prevent scratching and damage. 2. Release the roller bushing, rotate the busing up, and then slide the bushing off of the roller shaft. Figure 2-64 Remove the Tray 2, Tray 3, or Tray 4 pickup roller (1 of 3) 88 Chapter 2 Removal and replacement ENWW
3.Carefully remove the black-plastic guard (callout 1). CAUTION: The guard is partially retained by the bushing removed in the previous step. Do not lose the guard when the bushing is removed. Figure 2-65 Remove the Tray 2, Tray 3, or Tray 4 pickup roller (2 of 3) 1 4. Slide the roller toward the left side of the product, rotate the right end of the roller away from the product, and then remove the roller assembly. Figure 2-66 Remove the Tray 2, Tray 3, or Tray 4 pickup roller (3 of 3) ENWW Removal and replacement procedures 89
Tray 2, Tray 3, or Tray 4 separation pad CAUTION:Do not touch the surface of the pad. Skin oils deposited on the roller might cause paper- handling problems. 1. Remove the tray cassette. See Tray cassette (Tray 2, Tray 3, or Tray 4) on page 54. 2. Remove two screws (callout 1), and then remove the separation pad (callout 2). Figure 2-67 Remove the Tray 2, Tray 3, or Tray 4 separation pad 1 2 90 Chapter 2 Removal and replacement ENWW
Tray 2, Tray 3, or Tray 4 base-plate roller assembly 1.Remove the tray cassette. See Tray cassette (Tray 2, Tray 3, or Tray 4) on page 54. 2. Locate the base roller assembly (callout 1), release one tab (callout 2), and then slide the assembly toward the outside of the product to release it. Figure 2-68 Tray 2, Tray 3, or Tray 4 base plate roller assembly (1 of 2) 2 1 3.Remove the base roller assembly. Figure 2-69 Tray 2, Tray 3, or Tray 4 base plate roller assembly (2 of 2) ENWW Removal and replacement procedures 91
Transfer roller CAUTION:Do not touch the black-sponge portion of the transfer roller. Skin oils deposited on the transfer roller might cause print-quality problems. 1. Press the cartridge-door release button, and then open the cartridge door. Make sure that the door is completely open. NOTE: If you did not remove the print cartridge before servicing the product, remove it now. Figure 2-70 Remove the transfer roller (1 of 3) 2.Release two tabs (callout 1) at the left end of the roller, slightly lift the end of the roller up, and then slide the roller (callout 2) toward the left to release it. Remove the roller. Figure 2-71 Remove the transfer roller (2 of 3) 1 2 92 Chapter 2 Removal and replacement ENWW
3.If necessary, remove the gear, the bushing, and the spring, and then install them on a replacement roller. Figure 2-72 Remove the transfer roller (3 of 3) ENWW Removal and replacement procedures 93
USB port PCA WARNING! ESD sensitive component. 1.Before proceeding, remove the following components: ●DIMM cover. See DIMM cover and DIMM on page 57 . ● Formatter cover. See Formatter cover and formatter PCA on page 60. ● Top-right cover. See Top-right cover on page 73 . ● Control panel. See Control panel on page 74. ● Front-right and right-side cover assembly. See Front-right and right-side cover assembly on page 76 . 2. Release the wire harness (callout 1) from the retainers (callout 2). Figure 2-73 Remove the USB port PCA (1 of 3) 21 94 Chapter 2 Removal and replacement ENWW
3.Remove on screw (callout 1). Figure 2-74 Remove the USB port PCA (2 of 3) 1 4.Carefully remove the USB port PCA. Figure 2-75 Remove the USB port PCA (3 of 3) ENWW Removal and replacement procedures 95
Power-switch assembly WARNING! ESD sensitive component. 1.Before proceeding, remove the following components: ●DIMM cover. See DIMM cover and DIMM on page 57 . ● Formatter cover. See Formatter cover and formatter PCA on page 60. ● Top-right cover. See Top-right cover on page 73 . ● Control panel. See Control panel on page 74. ● Front-right and right-side cover assembly. See Front-right and right-side cover assembly on page 76 . 2. Disconnect one connector (callout 1), and then remove one screw (callout 2). Figure 2-76 Remove the power-switch assembly (1 of 2) 1 2 96 Chapter 2 Removal and replacement ENWW