HP Officejet 7413 User Manual

1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
CautionDo not touch the copper-colored contacts or ink nozzles.
Touching these parts can result in clogs, ink failure, and bad electrical
connections.
7 Slide the new print cartridge down the ramp and into the empty slot. Push the print
cartridge forward until it clicks into place.
If the print cartridge you are installing has  a white triangle on its label, slide the
print cartridge...

9 Close the print-carriage access door.
Use a photo print cartridge    
You can optimize the quality of the color photos you print and copy with your HP all-in-
one by purchasing a photo print cartridge. Remove the black print cartridge and insert
the photo print cartridge in its place. With the tri-color print cartridge and photo print
cartridge installed, you have a six-ink system, which provides enhanced quality color
photos.
When you want to print regular text documents,  swap the black print...

When you want to print regular text documents, swap the black print cartridge back in.
Use a print cartridge protector to keep your  print cartridge secure when it is not being
used.
● For more information on purchasing a gray photo print cartridge, see  Order print
cartridges .
● For more information on replacing print cartridges, see  Replace the print cartridges.
● For more information on using the print cartridge protector, see  Use the print
cartridge protector .
Use the print cartridge protector...

Align the print cartridges    
The HP all-in-one prompts you to align cartridges every time you install or replace a
print cartridge. You can also align the print cartridges at any time from the control panel
or by using the  HP Image Zone  software on your computer. Aligning the print cartridges
ensures high-quality output.
Note If you remove and reinstall the same print cartridge, the HP all-in-one will not
prompt you to align the print cartridges. The HP all-in-one remembers the
alignment values for...

For information on cleaning the print cartridge contacts, see Clean the print
cartridge contacts . For information on replacing the print cartridges, see  Replace
the print cartridges .
For information on cleaning the print cartridges by using the  HP Image Zone software
that came with your HP all-in-one, see the onscreen  HP Image Zone Help that came
with your software.
Clean the print cartridge contacts   
Clean the print cartridge contacts only if you get repeated messages on the color
graphics...

1Copper-colored contacts
2Ink nozzles (do not clean)
8 Place the print cartridge back into the print carriage slot and close the latch.
9 Repeat if necessary for the other print cartridge.
10 Gently close the print-carriage access door and plug the power cord into the back of the HP all-in-one.
Clean the area around the ink nozzles   
If the HP all-in-one is used in a dusty environment, a small amount of debris might
accumulate inside the device. This debris can include dust, hair, carpet, or clothing...

3 Lift one of the latches to the open position, and then remove the print cartridge.Note Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the
HP all-in-one for more than 30 minutes.
4 Place the print cartridge on a piece of paper with the ink nozzles facing up.
5 Lightly moisten a clean foam rubber swab with distilled water.
6 Clean the face and edges around the ink nozzle area with the swab, as shown...

You can choose 1, 4, 8, or 12 hours for the power save time.
Set the prompt delay time  
The Prompt Delay Time  option allows you to control the amount of time that passes
before a message prompts you to take further action. For example, if you press  Menu in
the Copy area and the prompt delay time passes without you pressing another button,
the message  Press START COPY to copy. Press Number or OK to select.  appears
in the color graphics display. You can choose  Fast, Normal , Slow , or Off. If you...

16Troubleshooting information 
This chapter contains troubleshooting information for the HP all-in-one. Specific
information is provided for installation and configuration issues, and some operational
topics. For more troubleshooting information, see the onscreen HP Image Zone Help.
Many issues are caused when the HP all-in-one is connected to the computer using a
USB cable before the HP all-in-one software is installed on the computer. If you
connected the HP all-in-one to your computer before the...

–HP Image Zone Help : The onscreen HP Image Zone Help  describes how to
use the HP all-in-one with a computer and contains additional troubleshooting
information not covered in the User Guide.
– Readme file : The Readme file contains information on possible installation
problems. For more information, see  View the Readme file.
2 If you are unable to solve the problem using the information in the documentation, visit www.hp.com/support  to do the following:
– Access online support pages
– Send HP an...