HP Color LaserJet CP6015dn User Manual

							ItemSub-itemValuesDescription
AUTO IP: A link-local IP address 169.254.x.x is set.
LEGACY : The address 192.0.0.192 is set, consistent
with older HP Jetdirect products.
  DHCP RELEASE
● NO
● YESThis menu appears if CONFIG METHOD
 was set to
DHCP  and a DHCP lease for the print server exists.
NO *: The current DHCP lease is saved.
YES: The current DHCP lease and the leased IP
address are released.
  DHCP RENEW
● NO
● YESThis menu appears if CONFIG METHOD
 was set to
DHCP  and a DHCP lease for the print server exists.
NO *: The print server does not request to renew the
DHCP lease.
YES: The print server requests to renew the current
DHCP lease.
  MANUAL SETTINGS
● IP ADDRESS
● SUBNET MASK
● SYSLOG SERVER
● DEFAULT
GATEWAY
● IDLE TIMEOUT(Available only if CONFIG METHOD
 is set to
MANUAL ) Configure parameters directly from the
printer control panel:
IP ADDRESS : The unique IP address of the printer,
where n is a value from 0 to 255.
SUBNET MASK : The subnet mask for the printer,
where m is a value from 0 to 255.
SYSLOG SERVER : The IP address of the syslog
server used to receive and log syslog messages.
DEFAULT GATEWAY : The IP address of the gateway
or router used for communica tions with other networks.
IDLE TIMEOUT : The time period, in seconds, after
which an idle TCP print data connection is closed
(default is 270 seconds, 0  disables the timeout).
  PRIMARY DNSSpecify the IP address (n.n.n.n) of a Primary DNS
Server.
  SECONDARY DNSSpecify the IP address (n.n.n.n) of a Secondary
Domain Name System (DNS) Server.
 IPV6 SETTINGSENABLE
●OFF
● ONUse this item to enable or disable IPv6 operation on the
print server.
OFF
*: IPv6 is disabled.
ON : IPv6 is enabled.
  ADDRESS
●MANUAL
SETTINGS
● ADDRESS Use this item to manually configure an IPv6 address.
Use the 
MANUAL SETTINGS  menu to enable and
manually configure a TCP/ IPv6 address.
Select  ENABLE  and choose  ON to enable manual
configuration, or OFF  to disable manual configuration.
Table 2-1  Embedded Jetdirect and EIO   Jetdirect menus (continued)
ENWW Configure device menu 37
 
						

							ItemSub-itemValuesDescription
ADDRESS: Use this item to type a 32 hexadecimal
digit IPv6 node address that uses the colon
hexadecimal syntax.
  DHCPV6 POLICY
● ROUTER
SPECIFIED
● ROUTER
UNAVAILABLE
● ALWAYSROUTER SPECIFIED
: The stateful auto-configuration
method to be used by the print server is determined by
a router. The router specifies whether the print server
obtains its address, its conf iguration information, or
both from a DHCPv6 server.
ROUTER UNAVAILABLE : If a router is not available,
the print server should attempt to obtain its stateful
configuration from a DHCPv6 server.
ALWAYS : Whether or not a router is available, the print
server always attempts  to obtain its stateful
configuration from a DHCPv6 server.
  PRIMARY DNSUse this item to specify an IPv6 address for a primary
DNS server that the print server should use.
  SECONDARY DNSUse this item to specify an IPv6 address for a
secondary DNS server that the print server should use.
 PROXY SERVER Specifies the proxy server to be used by embedded
applications in the product. A proxy server is typically
used by network clients for Internet access. It caches
Web pages, and provides a degree of Internet security,
for those clients.
To specify a proxy server, enter its IPv4 address or
fully-qualified domain name. The name can be up to
255 octets.
For some networks, you might need to contact your
Internet Service Provider (ISP) for the proxy server
address.
PROXY PORT Type the port number used by the proxy server for
client support. The port number identifies the port
reserved for proxy activity on your network, and can be
a value from 0 to 65535.
IPX/SPXENABLEOFF
ONOFF : Disable the IPX/SPX protocol.
ON *: Enable the IPX/SPX protocol.
FRAME TYPEAUTO
EN_8023
EN_II
EN_8022
EN_SNAPSelects the frame-type setting for your network.
AUTO : Automatically sets and  limits the frame type to
the first one detected.
EN_8023 , EN_II, EN_8022, and  EN_SNAPare frame-
type selections for Ethernet networks
APPLETALKENABLEOFF
ONOFF : Disable the AppleTalk protocol.
ON *: Enable the AppleTalk protocol.
DLC//LLC ENABLEOFF
ON OFF
: Disable the DLC/LLC protocol.
ON *: Enable the DLC/LLC protocol.
Table 2-1   Embedded Jetdirect and EIO  Jetdirect menus (continued)
38 Chapter 2   Control panel ENWW
 
						

							ItemSub-itemValuesDescription
SECURITYPRINT SEC PAGEYES
NOYES: Prints a page that contains the current security
settings on the HP Jetdirect print server.
NO*: A security settings page is not printed.
 SECURE WEBHTTPS REQUIRED
HTTP/HTTPS
OPTIONALFor configuration management, specify whether the
embedded Web server will accept communications
using HTTPS (Secure HTTP) only, or both HTTP and
HTTPS.
HTTPS REQUIRED : For secure, encrypted
communications, only HTTPS access is accepted. The
print server will appear as a secure site.
HTTP/HTTPS OPTIONAL : Access using either HTTP
or HTTPS is permitted.
 IPSECKEEP
DISABLESpecify the IPsec or Firewall status on the print server.
KEEP : IPsec/Firewall status remains the same as
currently configured.
DISABLE : IPsec/Firewall operation on the print server
is disabled.
 RESET SECURITYNO
YESSpecify whether the current security settings on the
print server will be saved or reset to factory defaults.
NO *: The current security settings are maintained.
YES: Security settings are reset to factory defaults.
DIAGNOSTICSEMBEDDED TESTSEXECUTEThis menu provides tests to help diagnose network
hardware or TCP/IP network connection problems.
Embedded tests help to identify whether a network fault
is internal or external to the product. Use an embedded
test to check hardware and communication paths on
the print server. After you select and enable a test and
set the execution time, you must select  EXECUTE to
initiate the test.
Depending on the execution time, a selected test runs
continuously until either the product is turned off, or an
error occurs and a diagnostic page is printed.
  LAN HW TESTCAUTION: Running this embedded test will erase
your TCP/IP configuration.
This test performs an internal loopback test. An internal
loopback test will send and receive packets only on the
internal network hardware. There are no external
transmissions on your network.
Select  YES to choose this test, or NO  to not choose it.
  HTTP TESTThis test checks operation of HTTP by retrieving
predefined pages from the product, and tests the
embedded Web server.
Select  YES to choose this test, or NO  to not choose it.
  SNMP TEST This test checks operation of SNMP communications
by accessing predefined SNMP objects on the product.
Table 2-1  Embedded Jetdirect and EIO   Jetdirect menus (continued)
ENWW Configure device menu 39
 
						

							ItemSub-itemValuesDescription
Select YES to choose this test, or NO  to not choose it.
  DATA PATH TESTThis test helps to identify data path and corruption
problems on an HP postscript level 3 emulation
product. It sends a predefined PS file to the product,
However, the test is paperless; the file will not print.
Select YES to choose this test, or NO  to not choose it.
  SELECT ALL TESTSSelect this item to run all the embedded tests. Select
YES to run all tests, or select NO to not run all tests.
  EXECUTION TIME [H]Use this item to specify the length of time (in hours) that
an embedded test will be run. You can select a value
from 1 to 60 hours. If you select zero (0), the test runs
indefinitely until an error occurs or the product is turned
off.
Data gathered from the HTTP, SNMP, and Data Path
tests is printed after the tests have completed.
  EXECUTENO*: Do not initiate the selected tests.
YES: Initiate the selected tests.
 PING TEST This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response.
  DEST TYPESpecify whether the target device is an IPv4 or IPv6
node.
  DEST IPV4Type the IPv4 address.
  DEST IPV6Type the IPv6 address.
  PACKET SIZESpecify the size of each packet, in bytes, to be sent to
the remote host. The minimum is 64 (default) and the
maximum is 2048.
  TIMEOUTSpecify the length of time, in seconds, to wait for a
response from the remote host. The default is 1 and
the maximum is 100.
  COUNTSpecify the number of ping test packets to send for this
test. Select a value from 1 to 100. To configure the test
to run continuously, select 0.
  PRINT RESULTSIf the ping test was not set for continuous operation,
you can choose to print the test results. Select  YES to
print results. If you select  NO (default), results are not
printed.
  EXECUTESpecify whether to initiate the ping test. Select  YES to
initiate the test, or  NO to not run the test.
 PING RESULTS Use this item to view the ping test status and results
using the control panel display.
   PACKETS SENTShows the number of packets (0 - 65535) sent to the
remote host since the most recent test was initiated or
completed.
Table 2-1  Embedded Jetdirect and EIO  Jetdirect menus (continued)
40 Chapter 2   Control panel ENWW
 
						

							ItemSub-itemValuesDescription
  PACKETS RECEIVEDShows the number of packets (0 - 65535) received from
the remote host since the most recent test was initiated
or completed.
  PERCENT LOSTShows the percent of ping test packets that were sent
with no response from the remote host since the most
recent test was initiated or completed.
  RTT MINShows the minimum detected roundtrip- time (RTT),
from 0 to 4096 milliseconds, for packet transmission
and response.
  RTT MAXShows the maximum detected roundtrip- time (RTT),
from 0 to 4096 milliseconds, for packet transmission
and response.
  RTT AVERAGEShows the average round-trip-time (RTT), from 0 to
4096 milliseconds, for packet transmission and
response.
  PING IN PROGRESSShows whether a ping test is in progress.  YES
indicates a test in progress, and  NO indicates that a
test completed or was not run.
  REFRESHWhen viewing the ping test results, this item updates
the ping test data with current results. Select  YES to
update the data, or  NO to maintain the existing data.
However, a refresh automatically occurs when the
menu times out or you manually return to the main
menu.
LINK SPEED AUTO
10T HALF : 10 Mbps, half-
duplex operation.
10T FULL: 10 Mbps, full-
duplex operation.
100TX HALF : 100 Mbps,
half-duplex operation.
100TX FULL : 100 Mbps,
full-duplex operation.
100TX AUTO : Limits
auto-negotiation to a
maximum link speed of
100 Mbps.
1000TX FULL : 1000
Mbps, full-duplex
operation.The link speed and communication mode of the print
server must match the network. The available settings
depend on the product and installed print server. Select
one of the following link configuration settings:
CAUTION: If you change the link setting, network
communications with the print server and network
device might be lost.
AUTO *: The print server uses auto-negotiation to
configure itself with the highest link speed and
communication mode allowed. If auto-negotiation fails,
either 100TX HALF or 10TX HALF is set depending on
the detected link speed of the hub/switch port. (A
1000T half-duplex selection is not supported.)
PRINT PROTOCOLS    Use this item to print a page that lists the configuration
of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
Resets menu
The RESETS  menu allows you to reset factory settings, disable and enable sleep mode, and update
the product after new supplies are installed.
Table 2-1   Embedded Jetdirect and EIO   Jetdirect menus (continued)
ENWW Configure device menu 41
 
						

							To display: Press Menu , select CONFIGURE DEVICE , and then select RESETS.
ItemValuesDescription
RESTORE FACTORY SETTINGS Allows you to clear the page buffer, remove
all perishable personality data, reset the
printing environment, and return all default
settings to factory defaults.
RESET CALIBRATION Resets calibration values on the formatter.
SLEEP MODE OFF
LOW
HIGH If 
SLEEP MODE  is OFF , the product will
never enter power save mode and no
asterisk will appear next to any item when
the user enters the menu item  SLEEP
DELAY .
The  LOW  setting has a shorter wake-up
time than the HIGH  setting. The default
setting is either  LOW or HIGH , depending
on your country/region.
42 Chapter 2   Control panel ENWW
 
						

							Diagnostics menu
The DIAGNOSTICS menu allows you to run tests that can help you identify and solve problems with
the product.
To display:  Press Menu  and then select  DIAGNOSTICS.
ItemSub-itemValuesDescription
PRINT EVENT LOG  Prints a report containing the last
50 entries in the product’s event
log, starting with the most recent.
SHOW EVENT LOG  Displays the last 50 events, starting
with the most recent.
PQ TROUBLESHOOTING  Prints a page that includes
instructions, pages for each color,
a demo page, and a configuration
page. These pages can help isolate
print-quality problems.
PRINT DIAGNOSTICS
PAGE  Prints a page that can assist in
diagnosing product problems.
DISABLE CARTRIDGE
CHECK  This item allows you to remove a
print cartridge to help determine
which cartridge is the source of a
problem.
PAPER PATH SENSORS  Performs a test on each of the
product’s sensors to determine if
they are working correctly and
displays the status  of each sensor.
PAPER PATH TEST  Tests the paper-handling features
of the product, such as the
configuration of the trays.
 PRINT TEST PAGE Generates a page for testing the
paper-handling features. You must
define the path for the test in order
to test specific paper paths.
 SOURCEALL TRAYS
TRAY 1
TRAY 2
(Additional trays are shown, if
applicable.)Specifies whether the test page is
printed from all trays or from a
specific tray.
 DESTINATIONALL BINS
(Additional bins are shown, if
applicable.)Appears if there is an optional
output accessory connected to the
product.
Selects the output option for the
test page. You can send the test
page to all output bins or only to a
specific bin.
  DUPLEX OFF
ON Determines whether the duplexer
is included in the test.
ENWW
Diagnostics menu 43
 
						

							ItemSub-itemValuesDescription
 COPIES1
10
50
100
500Determines how many pages
should be sent from the specified
source as part of the test.
FINISHING PAPER PATH
TEST  This item only appears if there is an
optional stapler/stacker or booklet
maker connected to the product.
Tests the paper-handling features
on the output accessory.
 STACKDESTINATION BIN
MEDIA SIZE
MEDIA TYPE
COPIES
DUPLEX
PRINT TEST PAGESets up the options for testing the
stapler/stacker or booklet maker
paper path.
After setting up all of the options,
select PRINT TEST PAGE  to run
the test.
 STAPLESFINISHING OPTIONS
DESTINATION BIN
MEDIA SIZE
MEDIA TYPE
COPIES
DUPLEX
PRINT TEST PAGESets up the options for testing the
stapler/stacker or booklet maker
stapling functions.
After setting up all of the options,
select  PRINT TEST PAGE  to run
the test.
 BOOKLET MAKER  (booklet
maker only)MEDIA SIZE
MEDIA TYPE
COPIES
DUPLEX
PRINT TEST PAGESets up the options for testing the
booklet-making functions of the
booklet maker.
After setting up all of the options,
select  PRINT TEST PAGE  to run
the test.
MANUAL SENSOR TEST  Performs tests to determine
whether the paper path sensors are
operating correctly.
MANUAL SENSOR TEST
2  Performs additional tests to
determine whether the paper path
sensors are operating correctly.
COMPONENT TEST TRANSFER MOTORS
BELT ONLY
IMAGE DRUM MOTORS  
Activate individual parts
independently to isolate noise,
leaking, and other hardware
issues.
44 Chapter 2   Control panel ENWW
 
						

							ItemSub-itemValuesDescription
BLACK LASER SCANNER
CYAN LASER SCANNER
MAGENTA LASER SCANNER
YELLOW LASER SCANNER
FUSER MOTOR
FUSER PRESSURE RELEASE
MOTOR
BLACK ALIENATION MOTOR
CYAN ALIENATION MOTOR
MAGENTA ALIENATION MOTOR
YELLOW ALIENATION MOTOR
ITB CONTACT/ALIENATION
PAPER TRANSPORT MOTOR
TRAY 1 PICKUP SOLENOID
TRAY 2 PICKUP MOTOR
TRAY 2 PICKUP SOLENOID
TRAY 3 PICKUP MOTOR
TRAY 3 PICKUP SOLENOID
TRAY 4 PICKUP MOTOR
TRAY 4 PICKUP SOLENOID
TRAY 5 PICKUP MOTOR
TRAY 5 PICKUP SOLENOID
DUPLEXER REVERSE MOTOR
DUPLEXER REFEED MOTOR
 REPEATONCE (default)
CONTINUOUSAllows the user to specify the
number of times the device
sequences. To terminate the test at
any time the user can press  Stop.
PRINT/STOP TEST Range is 0 - 60,000 milliseconds.
The default is 0.Isolates print quality faults more
accurately by stopping the product
in mid-print cycle, which allows you
to see where the image begins to
degrade. This causes a jam
message that might need to be
manually cleared. A service
representative should perform this
test.
COLOR BAND TEST PRINT TEST PAGE   Prints a color band test page that is
used to identify arcing in the high-
voltage power supply.
ENWW Diagnostics menu 45
 
						

							ItemSub-itemValuesDescription
 COPIESRange is 1 to 30. The default value
is 1.Allows the user to determine how
many copies of the internal page
are printed.
FINISHER TESTS  If the optional stapler/stacker or
booklet maker is installed, this
menu runs tests on specific
sensors and components. Different
values are displayed, based on the
accessory installed.
 MANUAL SENSOR TESTREAD ALL ONCE
CONTINUOUS READINGInitiates a diagnostic test of the
sensors on the stapler/stacker or
booklet maker.
 COMPONENT TESTS M1 - DELIVER MOTOR  (booklet
maker only)
M2 - FOLDING MOTOR  (booklet
maker only)
M3 - GUIDE MOTOR  (booklet
maker only)
M4 - GUIDE PLATE MOTOR
(booklet maker only)
M9 - INLET MOTOR (booklet
maker only)
M31 - ENTRANCE MOTOR
M36 - SWING MOTOR
M37 - TRAY 1 MOTOR
M38 - TRAY 2 MOTOR
M39 - PROCESS MOTOR
SL1 - FLAPPER 1 SOLENOID
(booklet maker only)
SL2 - FLAPPER 2 SOLENOID
(booklet maker only)
SL4 - BOOKLET SOLENOID
(booklet maker only)
SL5 - SWITCH SOLENOID
(booklet maker only)
SL31 - ROLLER 1A SOLENOID
SL32 - BUFFER SOLENOID
SL33 - OUTPUT SOLENOID
SL34 - GUIDE SOLENOID Activates a diagnostic test for the
selected motor or solenoid.
46 Chapter 2   Control panel
ENWW