HP Color LaserJet CP6015dn User Manual
Have a look at the manual HP Color LaserJet CP6015dn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Install memory You can install more memory for the product by adding a dual inline memory module (DIMM). CAUTION:Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal on the product. Install DDR memory DIMMs 1. Turn the product off. 2.Disconnect all power and interface cables. ENWW Replace supplies 157
3.Locate the black formatter pressure release tabs on the formatter board in the rear of the product. 4.Gently press the black tabs toward each other. 5.Gently pull on the black tabs to pull the formatte r board from the product. Place the formatter board on a clean, flat, grounded surface. 158 Chapter 11 Manage and maintain the product ENWW
6.If you are adding a DIMM to slot 2, locate the hard disk release tab on the bottom of the formatter board, and then pinch the tab to release the end of the hard disk assembly. 7. Rotate the end of the hard disk assembly upward until you can disengage the hinge tabs at the other end. 8. Leaving the hard disk assembly plugged in, lay it to the side to allow space to add or replace the DIMM in slot 2. 9. To replace a DIMM that is currently installed in either slot, spread the latches apart on each side of the DIMM, lift the DIMM up at an angle, and pull it out. XOXOXOXOXOXO XOXOXOXOXOXO XO XOXO XOXO XOXOXOXOXO XOXOXOXOXO XOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXOXOXOXOXO XOXOXO XOXOXOXOXOXO XOXOXO XOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXOXO XO XO XOXOXOXOXO 10. Remove the new DIMM from the antistatic pack age. Locate the alignment notch on the bottom edge of the DIMM. ENWW Replace supplies 159
11.Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an angle and firmly press the DIMM into the slot until it is fully seated. When installed correctly, the metal contacts are not visible. XOXOXOXOXOXO XOXOXOXOXOXO XO XOXO XOXO XOXOXOXOXO XOXOXOXOXO XOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXOXOXOXOXOXOXO XOXOXO XOXOXOXOXOXO XOXOXO XOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXO XO XOX OXOXOXO 12. Push down on the DIMM until both latches engage the DIMM. XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXOXOXOXOXO XOXOXO XOXOXOXOXOXO XOXOXO XOXOXO XOXOXOXO XOXO XOXOXOXOXOXOXOXO XOXO XO XOXOXOXOXO XIOXIOXIXO OXIXO XIOXIO XIOXIOXIXO OXIXO XIOXIO XIOXIOXIXO OXIXO XIOXIO XIOXIOXIXO OXIXO XIOXIO NOTE: If you have difficulty inserting the DIMM, ma ke sure the notch on the bottom of the DIMM is aligned with the bar in the slot. If the DIMM still does not go in, make sure you are using the correct type of DIMM. 13. If you had moved the hard disk assembly to access slot 2, re engage the hinge taps, and snap the release tab back into place on the formatter board. 14. Align the formatter board in the tracks at the bottom of the slot, and then slide the board back into the product. Be sure the pressure release tabs snap back into place. NOTE: To prevent damage to the formatter board, ensure the formatter board is aligned in the tracks. 160 Chapter 11 Manage and maintain the product ENWW
15.Reconnect the power cable and interface cables, and turn the product on. 16.To enable the new memory, see the following section. Enable memory for Windows 1.Windows XP and Windows Server 2003 (using the default Start menu view) : Click Start, click Settings, and then click Printers and Faxes. -or- Windows 2000, Windows XP, and Windows Server 2003 (using the Classic Start menu view) : Click Start, click Settings , and then click Printers. -or- Windows Vista : Click Start, click Control Panel , and then in the category for Hardware and Sound click Printer . 2. Right-click the driver icon, and then select Properties . 3. Click the Device Settings tab. 4. Expand the area for Installable Options. 5. Next to Printer Memory , select the total amount of memory that is installed. 6. Click OK. ENWW Replace supplies 161
Install an HP Jetdirect or EIO print server card or EIO hard disk This product is equipped with two external I/O (EIO ) slots. You can install an additional HP Jetdirect print server card or a hard disk in the available slots. 1. Turn the product off. 2.Disconnect all power and interface cables. 162 Chapter 11 Manage and maintain the product ENWW
3.Locate an open EIO slot. Loosen and remove the two retaining screws holding the cover for the EIO slot, and then remove the cover. You will not need these screws and the cover again. They can be discarded. 4.Firmly insert the HP Jetdirect print server card into the EIO slot. 5.Insert and tighten the retaining screws that came with the print server card. ENWW Replace supplies 163
6.Reconnect the power cable and remaining in terface cables, and turn the product on. 7.Print a configuration page. An HP Jetdirect confi guration page that contains network configuration and status information should also print. If it does not print, turn the product off, and then uninstall and reinstall the print server card to ensure that it is completely seated in the slot. 8. Perform one of these steps: ● Choose the correct port. See the computer or operating system documentation for instructions. ● Reinstall the software, choosing the network installation this time. Replace the staple cartridge If the optional HP 3-bin Stapler/Stacker Accessory or HP Booklet Maker/Finisher Accessory runs out of staples while it is stapling a print job, the product automatically stops, if set to stop when out. If the product is set to continue w hen out, the product will contin ue to print without stapling. NOTE:Only replace the staple cartridge unit when th e stapler/stacker or booklet maker has run out of staples. Removing the staple cartridge at other times can cause an error to occur. NOTE: When the stapler/stacker or bookle t maker runs out of staples, the stapler unit will return to its default position automatically. Replace the staple cartridge 1.Open the front door of the booklet maker or stapler/stacker. 164 Chapter 11 Manage and maintain the product ENWW
2.Push up to on the staple cartridge to remove it from the booklet maker or stapler/stacker. 3.Insert the replacement staple cartridge unit into the stapler unit. 4.Push the staple cartridge unit into the st apler unit until it clicks into position. 5.Close the front door. ENWW Replace supplies 165
Replace saddle stitch staple cartridges in the booklet maker 1.Open the front door of the booklet maker. 2.Grasp the blue handle and pull the staple carriage out of the booklet maker. 3.Grasp the small blue handle on the staple cartridge unit and pull it toward you, then swing the staple cartridge unit into an upright position. 2 1 4. Grasp the edges of each staple cartridge and pull up firmly to remove the staple cartridges from the staple cartridge unit. 166 Chapter 11 Manage and maintain the product ENWW