GE Vivid 7 Service Manual

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 3 - System Setup 3 - 137
3-13-2 Product Locator  Installation Card
NOTE: The Product Locator Installa tion Card shown may not be the same as the provided Product 
Locator card.
From the factory, a sheet with five Product Locator  cards for transportation and one for Installation are 
included. 
Figure 3-147   Product Locator Installation Card (Example) 

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
3 - 138 Section 3-13 - Installation Paperwork
3-13-3 Post Deli very Check List
Before shipment from the  factory, this product has been thorough ly tested and visually inspected. The 
product is a fine tuned electronic instrument and  should be treated properly during transportation.
To learn about any issues that are discovered at the reception of the package or when unpacking and 
installing the prod uct, the Post Delivery Chec...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 3 - System Setup 3 - 139
Figure 3-148   Post Delivery Checklist
GE Medical Systems
Document Number:  FC250559 01
POST DELIVERY CHECK LIST
Complete this form and send it to:
GE VINGMED ULTRASOUND AS
FAX NO.: +47 3302 1354
EMAIL:  [email protected]
ATTENTION: SYSTEM TEST DEPARTMENT
SYSTEM TESTER (USE BLOCK LETTERS): ____________________________________________ 
POST DELIVERY CHECK LIST FOR VIVID______________ SERIAL...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
3 - 140 Section 3-13 - Installation Paperwork
This page was intentionally left blank. 

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 4 - Functional Checks 4 - 1
Chapter 4 
Functional Checks
Section 4-1  
Overview
4-1-1 Purpose of Chapter 4
This chapter provides procedures for quickly checking major functions of the Vivid 7 scanner, 
diagnostics by using the built-in service software, and power supply adjustments. 
4-1-2 Contents in Chapter 4
4-1-3 Special Equipment Required
• An empty (blank) MO Disk; - P/N: 066E0519 (5.4 GB)
- P/N: 066E0514 (8.6 GB)
-...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
4 - 2 Section 4-2 - General Procedures
Section 4-2
General Procedures
4-2-1 Overview
Some procedures are used more often than other. The  intention with this section is to keep the most 
used procedures in one place.
NOTICESYSTEM REQUIRES ALL COVERS
Operate this unit only when all board covers and frame panels are securely in place. The covers are 
required for safe operation, good system performance and cooling purposes....

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 4 - Functional Checks 4 - 3
4-2-2 Power ON/ Boot UP
4-2-2-1 Connect Mains Power to the Scanner
    
NOTE: Do not cycle the Circuit Breake r ON-OFF-ON in less than five -5- seconds.   When turning OFF 
the Circuit Breaker, the system should de-energize  completely before turning the circuit breaker 
ON.
NOTE: When turning on a system from standby mode, it ta kes a few seconds before it responds. Do not push 
the On/off...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
4 - 4 Section 4-2 - General Procedures
4-2-2-1      Connect Mains Power to the Scanner (cont’d) 5.) Connect the Power Cable’s female plug to the Power Inlet at the rear of the unit.
6.) Lock the plug in position  with the Retaining Clasp.
7.) Verify that the Mains Power Circuit Breaker  is in OFF position, if not, switch it OFF.
8.) Connect the Power Cable’s other end (male plug ) to a hospital grade mains power outlet with the...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 4 - Functional Checks 4 - 5
4-2-2-2 Turn Unit On 1.) Switch ON the Mains Power Circuit  Breaker at the rear of the unit.
You should hear a “click” from the relays in the AC  Power/AC Controller and the unit is ready to boot.
NOTE: If the unit has been in the OFF co ndition for an extended period of time, (3 to 5 days or more), the unit 
may not boot, or may beep when turned on. 
2.) Press once on the  ON/STANDBY
 key on the...

GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
4 - 6 Section 4-2 - General Procedures
4-2-2-2      Turn Unit On (cont’d) f.) A start-up bar indicating the time used fo r software loading, is displayed on the monitor.
g.) The software initiates and se ts up the Front-End electronics and the rest of the instrument.
h.) The backlight in  the keyboard is lit.
i.) As soon as the software has been loaded, a 2D screen is displayed on the screen.
NOTE: Total time used for start-up is...