GE Logiq P5 Service Manual

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 125
8-3-5-3               Printer setting Back-up  (cont’d)
6.)  Select removable disk or other media.
7.)  Click the “Save” to write the printer configuration. Figure 8-172   Printer set backup
Figure 8-173   Printer set backup 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 126 Section 8-3 - Software Loading Procedure
8-3-5-3               Printer setting Back-up  (cont’d)
8.) Click the “OK” until all  printer windows are closed.
9.) If Sony D895 is used, repeat the step1  to setp4 and write down the Orientation set.
Figure 8-174   Printer set backup
Figure 8-175   Printer set backup 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 127
8-3-5-3               Printer setting Back-up  (cont’d)
10.)  Click the “Advanced”, then writhe down the Paper size and scaling parameters.
11.) Click “Properties” of the “Density Adjust”. Figure 8-176   Printer set backup
ParametersDescriptions
Orientation
Portrait or Landscape
Paper size Paper size
Scaling Rate of length and width
Table 8-52 Parameters
Figure 8-177   Printer set backup 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 128 Section 8-3 - Software Loading Procedure
8-3-5-3               Printer setting Back-up  (cont’d)
12.) Click “Save” -> select a remo vable disk or other media -> save the printer configuration.
13.) Click the “OK” until all  printer windows are closed.
14.) If the printer does not support the configuration  save or write option, write down or print out the 
following parameters.
NOTE: The parameters depend on printers, so the...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 129
Section 8-4Software Installation
8-4-1 Installing Base Image Software
NOTE: While we do not believe it  is necessary, It would not hurt to disconnect the system from the 
network and remove all transducers.
NOTE: All digital peripherals, reporting systems conn ected via the USB ports should be either power 
off or disconnected prior to the software installation
1.) Power ON the scanner....

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 130 Section 8-3 - Software Loading Procedure
8-4-1               Installing Base Image Software (cont’d)
4.) If the BIOS setting value in  Primary IDE Slave is ATAPI CDROM , the 1st Boot Device in Boot 
menu should be  Primary Slave. If the 1st Boot Device is not  Primary Slave, please change the 
setting value using  Enter key and Arrow key.
5.) If the BIOS setting value in  Secondary IDE Master is ATAPI CDROM, the 1st Boot...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 131
8-4-1               Installing Base Image Software (cont’d)
6.) Insert the BT11 Base Image Software Disk into t he CD/DVD ROM drive.
7.) After restarting th e system, the following sc reen will be displayed.
Figure 8-183   Boot Device Priority 
Figure 8-184   Installation Warning 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 132 Section 8-3 - Software Loading Procedure
8-4-1               Installing Base Image Software (cont’d)
8.) Press Enter key and then the  following screen will be shown. (If  you want to abort installation 
procedures, press CTRL+C.)
9.) Press  A key to install the complete disk. Figure 8-185   Base Image Software Inst
allation Menu
NOTICESelect A when installing the new HDD or upgrading from BT09. (HDD capacity should be...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 133
8-4-1               Installing Base Image Software (cont’d)
10.) Approx. twenty(20) minutes later, the following  screen appears. Eject the Base Image Software Disk 
from the CD/DVD ROM drive.
11.) After removing the disk from the drive, Press ALT + CTRL + DEL key.
NOTE: After Installing  Base Image Software, the “General failure  reading drive A. Abort, Retry, Fail?” 
message can be...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 134 Section 8-3 - Software Loading Procedure
8-4-2 Verifying Base Image Software
8-4-2-1 Partition Checks 1.) Reboot the SYSTEM and the Desktop screen will be shown as blow.
2.) Click Start  button and Run menu, then type  explorer and click OK
3.) Right-click  My Computer icon on the Desktop and click  Manage. 
Figure 8-188   Desktop Screen
Figure 8-189   Executing Windows Explorer
Figure 8-190   Opening the Manage Window