GE Logiq P5 Service Manual

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 145
8-4-4-2 Setting Computer Name 1.) Click on Utility, then  select Connectivity.
2.) Click on TCP/IP tab. 
3.) Type  Computer Name
4.) Verify that  Enable DHCP  has no check mark. If checked, remove the mark.
NOTE: If Enable DHCP mark is checked,  the system cannot checkout by VOLC.
5.) Check if  Computer Name, IP Address, Subnet Mask, and Default Gateway are proper ones 
which you wrote...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 146 Section 8-3 - Software Loading Procedure
8-4-4-3 Setting Printer Preferences NOTE: If the 1-3-5 printer setting back-up is NOT performed, i gnore this section.
1.) Insert removable disk or media that the printer setting was saved.
2.) Go to Utility -> System ->  Peripherals click the Printers.
3.) Press the left button of the trackball on the pr inter which need to be restore from the saved printer 
setting -> Click...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 147
8-4-4-3              Setting Printer Preferences  (cont’d)
5.) Select removable disk or media that the  printer setting was saved -> Click “Open”.
6.) Click the “OK” until all  printer windows are closed.
7.) If Sony D895 is used, repeat the above step 1 an d 3, then set the parameters below in the layout 
tab and advanced tab. Figure 8-206   Printer set restore
ParametersDescriptions...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 148 Section 8-3 - Software Loading Procedure
8-4-4-3              Setting Printer Preferences  (cont’d)
8.) Click the properties  of the Density Adjust”.
9.) Click “Load”.
10.) Select removable disk or media which the  printer setting was saved -> click “Open”.
11.) Click the “OK” until all  printer windows are closed.
Figure 8-207   Printer set restore
Figure 8-208   Printer set restore 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 149
8-4-4-3              Setting Printer Preferences  (cont’d)
12.) If the printer is not support restore option, restore the printer set from the recorded parameters.
NOTE: The parameters depend on printers, so the  above parameters are shown to another names and 
more parameters setting could be needed.
ParametersDescriptions
Orientation Portrait or Landscape
Paper size Paper size
Scaling...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 150 Section 8-3 - Software Loading Procedure
8-4-4-4 Functional Checks for Service Platform (Diagnostic Program) The Service platform uses a web-based user interface (UI) to provide access to common service 
components.
NOTE: After perform diagnostics,  shut down and restart to make the system working properly. 
1.) Go to Utility and press Service to launch Service  Platform. It will take some seconds for activating.
2.) Make...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 151
8-4-4-4              Functional Checks for Service Platform (Diagnostic Program)  (cont’d)
4.) Select GE Service  at the “Select User Level” field. 
5.) Enter the password for the Service Platform.
6.) Click on  Okay.
7.) Verify that the following screen (Servi ce Platform) is displayed on the monitor.
8.) Click on  x located at the upper right corner of the  service platform screen to...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 152 Section 8-3 - Software Loading Procedure
8-4-4-5 Setting the VCR (if necessary) 1.) Select Utility > System > Peripheral tab.
2.) Under Video Settings, PAL or NTSC.
3.) Under VCR, select Composite or S-Video.
4.) Under VCR, select Panasonic LQ-MD800  or Mitsubishi MD3000, as appropriate.
5.) Click on Save.
6.) Shut down the scanner, then restart the scanner.
7.) Verify that the VCR c an be properly operated.
8.) Perform the...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 153
8-4-4-6 Verifying the VCR (if necessary) 1.) Press Record button, VCR menu shows up at the bottom of the screen.
2.) Click Counter Reset, then Press  Record menu to start recording.
Displays a red dot in the VCR status area on the Title bar to indicate that recording has begun.
3.) Press Stop to stop recording the tape at the desired moment.
4.) Press Search to adjust the st arting time...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 154 Section 8-3 - Software Loading Procedure
8-4-4-7 Setting Printer Properties in Application Software (if necessary) 1.) Select Utility -> Connectivity -> Service tab
2.) Select Standard Printer, and Add
3.) Under Properties, select desired Printer, and Save. Figure 8-217   Utility > Connectivity > Service
Figure 8-218   Select the Printer