GE Logiq P5 Service Manual

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 135
8-4-2-1              Partition Checks  (cont’d)
4.) Select Storage -> Disk Management  and check that only File System, Status, Capacity  and 
Drive Letter  of each partition are same as follows
NOTE: If 160GB HDD is used, refer to the Figure 8-191.
NOTE: Repo partition and  CD/DVD-ROM Drives  Drive Letter should be assigned as Z:, G: 
respectively. Figure 8-191   Disk Management 160G HDD 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 136 Section 8-3 - Software Loading Procedure
8-4-2-2 Driver Checks 1.) On the window XP desktop, left click on My Computer then right click on Properties.
2.) The System Properties window appears. Select  Hardware > Device Manager.
3.) Verify that ?, X, or ! is not displayed
• If X or ! is displayed: - Left-click on the device with X mark, then right -click on  Enable
- Left-click on the device with ! mark, then right click on...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 137
8-4-2-3 USB Printer Checks (USB Printer User Only) Without any newly additional user in vention, LOGIQ™ P5 will recognize th e below 19 kinds of USB printer 
This procedure assumes that the P5 software  is installed and is functioning properly.
1.) Attach the USB cable from the printer to the USB port on assigned position
Printer NameComment
Sony UP-D895/D895MD Digital BW Printer
Sony...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 138 Section 8-3 - Software Loading Procedure
8-4-2-3              USB Printer Checks (USB Printer User Only)  (cont’d)
2.) Make sure that printer properties are proper. (I mage orientation and size). Refer to the latest 
Release Notes.
NOTICEOnce a USB printer is connected to one of the USB ports, dont take out the USB printer and plug it in 
another USB port.
Figure 8-193   USB Port - Rear Panel Connector
Figure 8-194   USB Port...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 139
8-4-2-4 DMC Checks (DMC User Only) NOTE: DMC Cable is supplied only as an option. 1.) Check DMC Cable (USB to Serial Bridge).
2.) Plug in the Cable as shown on the right side of the USB port.
3.) Ensure USB to Serial Bridge port  is recognized by the system.
4.) Trackball to My computer icon and left click
5.) Right click on  Properties.
6.) Right click on the  Hardware tab.
7.) Right...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 140 Section 8-3 - Software Loading Procedure
8-4-2-4              DMC Checks (DMC User Only)  (cont’d)
8.) Make sure“USB to Serial Bridge”  is displayed as shown the Figure 8-196
Figure 8-196   Device Manager Windows 

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 141
8-4-3 Installing Application Software
NOTE: First time SW installation with peripherals on can cause the BlueScreen.
NOTE: When connecting peripherals to the system, make sure to turn off the system first in order to avoid the  BlueScreen.
1.) Place the “Application Soft ware” CD into the DVD drive.
2.) Press the Start button on the tool bar at  the bottom of the LCD screen and select...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 142 Section 8-3 - Software Loading Procedure
8-4-3               Installing Application Software (cont’d)
7.) After copying backup files, the following options appear. 
8.) elect a product to be installed. 1.) LOGIQ P5 [R4.0.1] is only for LOGIQ P5 BT11 product.
2.) LOGIQ P5 [R3.0.4] is only for LOGIQ P5 BT09 product.
3.) LOGIQ A5 [R3.0.4] is only for LOGIQ A5 BT09 product.
4.) LOGIQ A5 Pro [R3.0.4] is only  for LOGIQ A5 PRO BT09...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1LOGIQ™ P5 SERVICE MANUAL 
Section 8-3 - Software Loading Procedure 8 - 143
8-4-3               Installing Application Software (cont’d)
12.) After the installa tion is completed the system  will power off automatically.
NOTE: Some of systems doesn’t power off automatica lly. In this case, press and hold power button 
more than 5 sec. to power off.
NOTE: Do not operate with using mouse or keyboard during installation procedures. 13.) Turn on the system and...

GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL  
8 - 144 Section 8-3 - Software Loading Procedure
8-4-4 Standard Confirma tion & Functional Checks
Configure the system settings and perform functi onal checks after installation of software.
Items for configuration and functional checks include: - Confirmation of the software version
- Preset Data (if necessary)
- Patient Image Data (if necessary)
- Functional Checks for Service Platform (Diagnostic Program)
8-4-4-1 Confirming...