Ford F650 Owners Manual
Have a look at the manual Ford F650 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 41 Ford manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
• Transmission temperature gauge: Displays the transmission fluid temperature at the transmission sump. • Hourmeter: Displays the hours of engine run time. • Voltmeter: Displays electrical system voltage. Information Display Odometer Located in the bottom of the information display. Registers the accumulated distance your vehicle has traveled. Trip Computer See General Information (page 64). Vehicle Settings and Personalization See General Information (page 64). Diesel Engines Engine oil pressure gauge. A Engine coolant temperature gauge. B Diesel Exhaust Fluid (DEF) gauge. C 58 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument ClusterE207382
Fuel gauge. D Speedometer. E Information display. F Tachometer. G Engine Oil Pressure Gauge Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). If the needle falls below the normal range, stop the vehicle, switch off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked by an authorized dealer. Engine Coolant Temperature Gauge WARNING Never remove the coolant reservoir cap while the engine is running or hot. Indicates engine coolant temperature. At normal operating temperature, the level indicator is in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Diesel Exhaust Fluid (DEF) Gauge Indicates the fluid level in the DEF tank. Fuel Gauge Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient. Switch the ignition on. The fuel gauge indicates approximately how much fuel is in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon. After refueling, some variability in needle position is normal: • It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station. • The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station. • If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle. Gauge Package (If Equipped) If your vehicle is equipped with the optional gauge package, it has some or all of the following gauges: • Transmission temperature gauge: Displays the transmission fluid temperature at the transmission sump. • Hourmeter: Displays the hours of engine run time. • Voltmeter: Displays electrical system voltage. Information Display Odometer Located in the bottom of the information display. Registers the accumulated distance your vehicle has traveled. 59 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument Cluster
Trip Computer See General Information (page 64). Vehicle Settings and Personalization See General Information (page 64). WARNING LAMPS AND INDICATORS The following warning lamps and indicators alert you to a vehicle condition that may become serious. Some lamps illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and operate the same as a warning lamp but do not illuminate when you start your vehicle. Anti-Lock Braking System If it illuminates when you are driving, this indicates a malfunction. Your vehicle continues to have normal braking without the anti-lock brake system function. Have your vehicle checked as soon as possible. Automatic Regeneration Control (If Equipped) Illuminates when you switch it off. Battery If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical equipment and have the system checked by an authorized dealer immediately. Brake System WARNING Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It may take you longer to stop your vehicle. Have your vehicle checked as soon as possible. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by an authorized dealer. Check Fuel Cap Illuminates when you may not have properly installed the fuel cap. Continued driving with this light on may cause the Service engine soon warning indicator to come on. Check Suspension (If Equipped) Illuminates when you press the air suspension dump switch. Cruise Control (If Equipped) Illuminates when you switch on this feature. See Using Cruise Control (page 137). Diesel Exhaust Fluid (If Equipped) Illuminates with the key in the ON position, when the fluid is contaminated or the level falls below 1.0 gal (3.8 L). Refill the tank or, at a minimum, add at least 1.0 gal (3.8 L) in the tank. 60 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument Cluster E208811 E209041 E208808 E71340 E163176
Diesel Particulate Filter (If Equipped) Illuminates when the soot level in the diesel particulate filter has reached a point where it requires operator assistance. See Diesel Particulate Filter (page 109). Direction Indicator Illuminates when you switch on the left or right direction indicator or when you switch on the hazard warning flashers. If the indicators stay on or flash faster, check for a burned out bulb. Door Ajar Displays when the ignition is on and any door is not completely closed. Electronic Locking Differential (If Equipped) Illuminates when using the electronic locking differential. Engine Oil Pressure If it illuminates with the engine running, or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch off the engine. Check the engine oil level. Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by an authorized dealer immediately. Exhaust Brake On (If Equipped) The exhaust brake indicator light illuminates when you switch the exhaust brake on. Fasten Seatbelt Illuminates and a tone sounds to remind you to fasten your seatbelt. High Beam Illuminates when you switch on the high beam headlamps. It flashes when you use the headlamp flasher. Hydromax Illuminates to indicate normal hydromax booster reserve system activation when the engine is off and the service brake pedal is applied. This light may also illuminate momentarily if the engine is running and the driver turns the steering wheel fully in one direction while braking. If the light remains on while the engine is running, this indicates inadequate hydraulic booster pressure or reserve pump system failure. Stop the vehicle as soon as possible and seek service immediately by your authorized dealer. Low Fuel Level (If Equipped) Illuminates when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as possible. Parking Brake Warning Illuminates briefly when you switch the ignition to the on position (with the engine off). It also illuminates when you apply the parking brake. If the park brake lamp does not illuminate at these times, seek service immediately. Vehicles equipped with the power park parking brake option: If the park brake warning lamp begins to blink after 61 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument Cluster E163170 E171217 E71880 E146190 E208810
setting the parking brake, this may indicate a failure in the parking brake system. Seek service from an authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Powertrain Malfunction/Reduced Power/Electronic Throttle Control (If Equipped) Illuminates in the event of a powertrain fault. Contact an authorized dealer as soon as possible. Service Engine Soon If it illuminates when the engine is running this indicates a malfunction. The On Board Diagnostics system has detected a malfunction of the vehicle emission control system. If it flashes, engine misfire may be occurring. Increased exhaust gas temperatures could damage the catalytic converter or other vehicle components. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle immediately serviced. It illuminates when you switch the ignition on prior to engine start to check the bulb and to indicate whether your vehicle is ready for Inspection and Maintenance (I/M) testing. Normally, it illuminates until the engine is cranked and automatically turns off if no malfunctions are present. However, if after 15 seconds it flashes eight times, this indicates that your vehicle is not ready for Inspection and Maintenance (I/M) testing. See Catalytic Converter (page 103). Stability Control and Traction Control Indicator (If Equipped) Illuminates and slowly flashes when you change the traction control mode. It illuminates and rapidly flashes during a traction or stability control event. Trailer Anti-Lock Brake System (ABS) Illuminates briefly when you switch on the ignition, and only when a PLC trailer or a PLC diagnostic tool is connected. If the light fails to illuminate, remains on after you start the vehicle or continues to flash, have the system serviced immediately. Transmission Tow/Haul (If Equipped) Illuminates when you switch on the tow/haul feature. If the light flashes steadily, have the system serviced immediately, damage to the transmission could occur. Two Speed Axle The Two Speed Axle indicator comes on when you switch the low axle range on. Wait to Start (If Equipped) Illuminates when you switch the ignition on as part of the pre-start system. Wait until the wait to start indicator turns off before attempting to start vehicle. WARNING Do not use starting fluid, for example ether, in the air intake system. Such fluid could cause immediate explosive damage to the engine and possible personal injury. 62 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument Cluster E138639 E209040 E161509 E208809
Water in Fuel (If Equipped) Illuminates when the fuel filter/water separator has a significant quantity of water in it. If the light illuminates when the engine is running, stop the vehicle as soon as safely possible, shut off the engine, then drain the fuel filter/water separator. Allowing water to stay in the system could result in extensive damage to, or failure of, the fuel injection system. WARNING Do not drain the water-in-fuel separator while the engine is running. Failure to follow this warning may result in fire, serious injury, death or property damage. AUDIBLE WARNINGS AND INDICATORS Beltminder Warning Sounds when a safety belt is unfastened in an occupied seat and your vehicle is moving. Door Ajar Sounds when a door is not fully closed and your vehicle is moving. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately. 63 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Instrument Cluster
GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving. You can control various systems on your vehicle using the information display controls on the steering wheel. The information display provides the corresponding information. Information Display Controls • Press the INFO button to scroll through trip, outside temperature and fuel usage information. • Press the SETUP button to scroll through various vehicle feature settings. • Press the RESET button to choose settings, reset information and confirm messages. Info Press the INFO button repeatedly to cycle through the following features: Note: Some options may appear slightly different or not at all if the items are optional. INFO TRIP A TRIP B XXX MILES (km) TO E XX.X AVG MPG (L/100km) MPG (L/km) TIMER EXHAUST FILTER * TRANS TEMP BATT. VOLTAGE BLANK SCREEN * Diesel engine only. 64 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Information Displays
TRIP A/B Registers the distance of individual journeys. Press and release the INFO button until TRIP A/B appears in the display (this represents the trip mode). Press and hold the RESET button to reset. XXX MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to detect the correct amount of added fuel. The system calculates the distance to empty by using a running average fuel economy, which uses your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy resets to a factory default value if the battery is disconnected. XX.X AVG MPG (L/100km) Average fuel economy displays your average fuel economy in miles per gallon or liters/100 km. MPG (L/km) Displays the instantaneous fuel economy as a bar graph. Your vehicle must be moving to calculate instantaneous fuel economy. You cannot reset the instantaneous fuel economy. TIMER Displays the trip elapsed drive time. Press and release RESET to pause the timer. Press and hold RESET to reset the timer. EXHAUST FILTER Displays information about the status of the exhaust filter. System Check and Vehicle Feature Customization Press the SETUP button repeatedly to cycle the information display through the following features: Note: Some options may appear slightly different or not at all if the items are optional. Note: When returning to the SETUP menu and you selected a non-English language, HOLD RESET FOR ENGLISH displays to change back to English. Press and hold the RESET button to change back to English. SETUP OIL LIFE Press the RESET button RESET FOR SYSTEM CHECK ENGINE HOURS DEF LEVEL* All DOORS CLOSED CHECK BRAKE SYSTEM HOLD RESET = NEW OIL LIFE English or Metric UNITS 65 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Information Displays
SETUP ON or OFF AUTO LOCK ON or OFF AUTO UNLOCK ON or OFF COURTESY WIPE ON or OFF REMOTE WINDOW ENGLISH / SPANISH / FRENCH LANGUAGE * Diesel engine only. PRESS RESET FOR SYSTEM CHECK The information display begins to cycle through the vehicle systems and provides a status of the item if needed. Note: Some systems show a message only if a condition is present. OIL LIFE Displays the remaining oil life. An oil change is required whenever indicated by the information display and according to the recommended maintenance schedule. Only use recommended engine oils. To reset the oil monitoring system to 100% after each oil change, perform the following: 1. Press and release the SETUP button to display OIL LIFE XXX% HOLD RESET = NEW. 2. Press and hold the RESET button for two seconds and release to reset the oil life to 100%. Note: To change oil life 100% value (if equipped with this feature) to another value, proceed to Step 3. 3. Once OIL LIFE SET TO XXX% is displayed, release and press the RESET button to change the Oil Life Start Value. Each release and press reduces the value by 10%. UNITS Displays the current units English or Metric. LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language the message center displays. Waiting four seconds or pressing the RESET button cycles the message center through each of the language choices. Press the RESET button to set the language choice. INFORMATION MESSAGES Note: Depending on your vehicle options and instrument cluster type, not all of the messages display or are available. Additionally, the information display may abbreviate or shorten certain messages. Press the RESET button to acknowledge and remove some messages from the information display. The information display automatically removes other messages after a short time. You need to confirm certain messages before you can access the menus. 66 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Information Displays
Diesel Messages WARNING When the CLEANING EXHAUST FILTER message appears in the information display, do not park near flammable materials, vapors or structures until filter cleaning is complete. Action Message The coolant additive needs checking. CHECK COOLANT ADDITIVE Your vehicle has entered the cleaning mode. Various engine actions raise the exhaust temperature in the diesel particulate filter system to burn off the particles (exhaust soot). After the vehicle burns off the particles, the exhaust temperature returns to normal levels. This message is normal. CLEANING EXHAUST FILTER The diesel particulate filter is full of particles (exhaust soot) and you are not operating the vehicle in a manner that allows normal cleaning. One of these messages stays on until the exhaust filter cleaning has begun, at which time the CLEANING EXHAUST FILTER message displays. We recommend you drive the vehicle above 30 mph (48 km/h) until the CLEANING EXHAUST FILTER message turns off. EXHAUST OVER- LOADED DRIVE TO CLEAN EXHAUST AT LIMIT DRIVE TO CLEAN NOW The diesel particulate filter continues to fill with particles (exhaust soot) if you ignore this message. The service engine soon light illuminates and engine power may be limited, if cleaning is not permitted. Your vehicle requires dealer service to restore it to full –power operation. Your vehicle exhaust system temperature exceeds intended operating range. If this warning occurs, a chime sounds, followed by reduced engine power. The engine shuts down when your vehicle speed is below 3 mph (5 km/h). Stop the vehicle as soon as safely possible. Have the system checked by an authorized dealer. STOP SAFELY NOW The diluted engine oil needs to be changed. ENGINE OIL DILUTED Your vehicle will have reduced engine torque until the engineis warmed sufficiently. ENGINE WARMING REDUCED POWER The powertrain control module intentionally turns the engineoff due to your vehicle being in the final 30 seconds of a countdown. The diesel engine shutdown for extended idling is an optional feature. ENGINE TURNS OFF IN XX SECONDS Appears after the 30–second countdown. ENGINE TURNED OFF 67 F650750 (TBC) , enUSA, Edition date: 201708, First Printing Information Displays