Home > Epson > Printer > Epson AcuLaser C2600N User Manual

Epson AcuLaser C2600N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C2600N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 473
    							Installing Options311
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    4. Identify the ROM module slots.
    Note:
    There are two ROM slots, and either slot can be used to attach the 
    ROM module.
    5. Insert the ROM module horizontally into the slot until the clip 
    comes out.
    c
    Caution:
    ❏Do not force the ROM module into the socket.
    ❏Be sure to insert the ROM module in the correct 
    direction.
    ❏Never remove the ROM module installed on the 
    standard ROM socket (P). 
     
    						
    							312Installing Options 6. Reattach the cover to the back side of the printer and secure 
    it with the four screws.
    7. Reconnect the power cord and turn the printer on.
    To confirm that the option is installed correctly, print a Status 
    Sheet. See  Printing a Status Sheet on page 370.
    If P5C is not listed as an installed emulation on the status sheet, 
    try reinstalling the module. Make sure that it is securely seated 
    into the ROM slot on the circuit board.
    Removing the P5C ROM module
    c
    Caution:
    Before you remove the ROM module, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    Turn off the printer and perform the installation procedure in 
    reverse.
     
    						
    							Replacing Consumable Products313
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    Chapter 9 
    Replacing Consumable Products
    Replacement Messages
    When you see the following messages on the LCD panel or the 
    window of EPSON Status Monitor 3, replace the appropriate 
    consumable products. You can continue to print for a short time 
    after a message appears, but Epson recommends early 
    replacement to maintain print quality and extend the life of your 
    printer.
    Note:
    To clear the warning, select Clear All Warning from the control 
    panel’s Reset Menu.
    If a consumable product reaches the end of its service life, the 
    printer stops printing and displays the following messages on the 
    LCD panel or the window of EPSON Status Monitor 3. When this 
    happens, the printer cannot resume printing until you replace the 
    depleted consumable products.
    LCD Panel Message Description
    Worn Photoconductor The photoconductor unit has reached the 
    end of its service life. 
    Worn Fuser The fuser unit has reached the end of its 
    service life. 
    Worn Transfer Unit The transfer unit is near the end of its service 
    life. 
     
    						
    							314Replacing Consumable Products
    * T h e  l e t t e r s  C ,  M ,  Y ,  o r  K  a p p e a r  i n  t h i s  p o s i t i o n ,  i n d i c a t i n g  t h e  c o l o r  o f  t h e  t o n e r  
    to be replaced. For example, the message Y Toner Low means that the 
    amount of toner remaining in the yellow toner cartridge is low.
    Note:
    Messages appear for one consumable product at a time. After replacing 
    a consumable product, check the LCD panel for replacement messages 
    for other consumable products.
    Even if Replace Toner uuuu or Replace Photoconductor is 
    displayed on the LCD panel, you can print an additional sheets 
    by pressing the NStart/Stop button on the control panel. The 
    message on the LCD panel changes from Replace Toner uuuu or 
    Replace Photocondctor to uuuu Toner Low or Worn 
    Photoconductor.
    Note:
    ❏Print quality cannot be guaranteed when printing with a worn 
    consumable product. If print quality is not what you expected, 
    replace the consumable product.
    ❏The printer stops printing if printing with a worn consumable 
    product might damage the printer. If the printer stops printing, 
    replace the consumable product.
    LCD Panel Message Description
    Replace Toner 
    uuuu*The indicated toner cartridges are empty.
    Replace 
    PhotoconductorPrinting has stopped to avoid damage to the 
    engine.
    Replace Waste T Box The waste toner collector is full.
     
    						
    							Replacing Consumable Products315
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    Toner Cartridge
    Handling precautions
    Always observe the following handling precautions when 
    replacing the consumable products:
    ❏Installing a genuine toner cartridge is recommended. Using a 
    non-genuine toner cartridge may affect print quality. Epson 
    shall not be liable for any damages or problems arising from 
    the use of consumable products not manufactured or 
    approved by Epson.
    ❏When handling toner cartridge, always place them on a clean 
    smooth surface.
    ❏If you have moved a toner cartridge from a cool to a warm 
    environment, wait for at least one hour before installing it to 
    prevent damage from condensation.
    w
    Warning:
    ❏Do not touch the toner. Keep the toner away from your eyes. 
    If toner gets on your skin or clothes, wash it off with soap and 
    water immediately.
    ❏Keep consumable products out of the reach of children.
    ❏Do not dispose of used consumable products in fire, as they 
    may explode and cause injury. Dispose of them according to 
    local regulations.
    ❏If toner is spilled, use a broom and dustpan or a damp cloth 
    with soap and water to clean it up. Because the fine particles 
    can cause a fire or explosion if they come into contact with a 
    spark, do not use a vacuum cleaner.
     
    						
    							316Replacing Consumable Products
    Replacing a toner cartridge
    Follow the steps below to replace a toner cartridge.
    1. Prepare a new cartridge of the color (K, C, M or Y) displayed on 
    the LCD panel.
    2. Open cover D.
    3. Hold the toner cartridge knob and tilt it toward you.
     
    						
    							Replacing Consumable Products317
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    4. Remove the empty toner cartridge from the printer.
    5. Take the protective materials off of the new cartridge, and 
    gently shake the new toner cartridge a few times.
    6. Take the new toner cartridge out of its package, and remove 
    the plastic protective cover from the toner cartridge.
     
    						
    							318Replacing Consumable Products 7. Insert the new cartridge into the printer.
    8. Close the toner cartridge cover.
     
    						
    							Replacing Consumable Products319
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9
    9. Close cover D.
      Photoconductor Unit
    Handling precautions
    Always observe the following handling precautions when 
    replacing the consumable products:
    ❏The photoconductor unit weighs 1.3 kg (2.9 lb). Be sure to hold 
    it firmly by the handle when carrying it.
    ❏When replacing the photoconductor unit, avoid exposing it 
    to room light any longer than three minutes. 
    ❏Be careful not to scratch the surface of the drum. Also, avoid 
    touching the drum, since oil from your skin may permanently 
    damage its surface and affect print quality.
    ❏To get the best print quality, do not store the photoconductor 
    unit in an area subject to direct sunlight, dust, salty air, or 
    corrosive gases (such as ammonia). Avoid locations subject to 
    extreme or rapid changes in temperature or humidity. 
     
    						
    							320Replacing Consumable Products ❏When storing the photoconductor unit, make sure to attach 
    the protective cover to the photoconductor unit and put it in 
    the sealed blackout package and the box in which the 
    photoconductor unit was sold, and store it in a safe level place. 
    ❏Do not tilt the photoconductor unit.
    w
    Warning:
    ❏Do not dispose of the used consumable products in fire, as it 
    may explode and cause injury. Dispose of it according to local 
    regulations.
    ❏Keep the consumable products out of the reach of children.
    Replacing the photoconductor unit
    Follow the steps below to replace the photoconductor unit, the 
    waste toner collector, and the filter.
    1. Open cover D.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C2600N User Manual